bonjour,
nous possedons un reseau de mngt d'equipements en 83.82.64.xx 255.255.255.224 decoupé en 6 sous reseaux
mon reseau admin est en 83.82.65.0 255.255.255.240 il est composé de 3 serveurs (83.82.65.3 83.82.65.4 83.82.65.5)et de pc d'administration 83.82.65.6 etc ..
nous avons ajouté 2 nouveaux equipements avec une @ip equipement et une @ip ethernet
cette derniere est dans un sous reseau en 83.82.64.xx
test:
quand je suis dans le reseau 83.82.64.xx j'arrive à me connecter sur mon equipement
quand je suis dans le reseau 83.82.65.xx impossible
j'ai donc ajouter 2 routes sur l'interface du routeur ping ok mais impossible de se connecter sur l'equipement
pour superviser je dois utiliser un logiciel pilot de chez sagem que j'ai installé sur mon pc supervision
il utilise le protocole SNMP
pouvez vous m'aidez?
merci d'avance
ci joint la conf du routeur
user Access Verification
Username: admin
Password:
% Password expiration warning.
-----------------------------------------------------------------------
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you want to
use.
-----------------------------------------------------------------------
ROUTER-SUP-FH#sh run
Building configuration...
Current configuration : 3593 bytes
!
! Last configuration change at 01:16:32 UTC Fri Jan 3 2014 by ADMIN
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname ROUTER-SUP-FH
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 $1$7Tf2$TjrSWRI8G3FflfkxpRXEB.
!
no aaa new-model
!
ip source-route
!
!
ip cef
!
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
!
!
license udi pid CISCO2811 sn FCZ14452106
username raphael privilege 15 secret 5 $1$K7/.$wc8iZkTvul2n/qoH7oZi80
username admin privilege 15 password 0 admin
!
!
!
!
!
!
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0/0$
ip address 83.82.65.1 255.255.255.240
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 83.82.64.1 255.255.255.224 secondary
ip address 83.82.64.65 255.255.255.224 secondary
ip address 83.82.64.97 255.255.255.224 secondary
ip address 83.82.64.129 255.255.255.224 secondary
ip address 83.82.64.161 255.255.255.224 secondary
ip address 83.82.64.193 255.255.255.224 secondary
ip address 192.168.0.1 255.255.0.0 secondary
ip address 192.168.0.2 255.255.0.0
duplex auto
speed auto
!
ip forward-protocol nd
!
!
ip http server
ip http access-class 23
ip http authentication local
ip http timeout-policy idle 60 life 86400 requests 10000
!
access-list 23 permit 10.10.10.0 0.0.0.7
access-list 101 permit udp any any eq ntp
access-list 101 permit udp any host 83.82.65.5 eq ntp
!
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you want to
use.
-----------------------------------------------------------------------
^C
banner login ^C
-----------------------------------------------------------------------
Cisco Configuration Professional (Cisco CP) is installed on this device.
This feature requires the one-time use of the username "cisco" with the
password "cisco". These default credentials have a privilege level of 15.
YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE PUBLICLY-KNOWN
CREDENTIALS
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want
to use.
IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE
TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
For more information about Cisco CP please follow the instructions in the
QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
-----------------------------------------------------------------------
^C
!
line con 0
login local
line aux 0
login local
line vty 0 4
access-class 23 in
privilege level 15
login local
transport input telnet
line vty 5 15
access-class 23 in
privilege level 15
login local
transport input telnet
!
scheduler allocate 20000 1000
end
