Charly303 Quand on veut on peut ! | Postfix
main.cf décommenté pour plus de lisibilité
Code :
- command_directory = /usr/sbin
- daemon_directory = /usr/libexec/postfix
- unknown_local_recipient_reject_code = 550
- alias_maps = hash:/etc/aliases
- alias_database = hash:/etc/aliases
- debug_peer_level = 2
- debugger_command =
- PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin
- xxgdb $daemon_directory/$process_name $process_id & sleep 5
- sendmail_path = /usr/sbin/sendmail.postfix
- newaliases_path = /usr/bin/newaliases.postfix
- mailq_path = /usr/bin/mailq.postfix
- setgid_group = postdrop
- html_directory = no
- manpage_directory = /usr/share/man
- sample_directory = /usr/share/doc/postfix-2.3.3/samples
- readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES
- mynetworks_style = host
- relayhost = [smtp.coditel.net]
- myorigin = $mydomain
- header_size_limit = 1024000
- qmgr_message_recipient_limit = 200000
- message_size_limit = 102400000
- mailbox_size_limit = 512000000
- home_mailbox = Mail/
|
dovecot.conf
Code :
- # Mes mails vont être lus ici !!!
- default_mail_env= maildir:/home/%u/Mail/
- ## Dovecot configuration file
- # If you're in a hurry, see http://wiki.dovecot.org/QuickConfiguration
- # '#' character and everything after it is treated as comments. Extra spaces
- # and tabs are ignored. If you want to use either of these explicitly, put the
- # value inside quotes, eg.: key = "# char and trailing whitespace "
- # Default values are shown for each setting, it's not required to uncomment
- # any of the lines.
- # Base directory where to store runtime data.
- #base_dir = /var/run/dovecot/
- # Protocols we want to be serving: imap imaps pop3 pop3s
- # If you only want to use dovecot-auth, you can set this to "none".
- #protocols = imap imaps pop3 pop3s
- # IP or host address where to listen in for connections. It's not currently
- # possible to specify multiple addresses. "*" listens in all IPv4 interfaces.
- # "[:]" listens in all IPv6 interfaces, but may also listen in all IPv4
- # interfaces depending on the operating system.
- #
- # If you want to specify ports for each service, you will need to configure
- # these settings inside the protocol imap/pop3 { ... } section, so you can
- # specify different ports for IMAP/POP3. For example:
- # protocol imap {
- # listen = *:10143
- # ssl_listen = *:10943
- # ..
- # }
- # protocol pop3 {
- # listen = *:10100
- # ..
- # }
- #listen = [:]
- listen = [:]
- # Disable LOGIN command and all other plaintext authentications unless
- # SSL/TLS is used (LOGINDISABLED capability). Note that if the remote IP
- # matches the local IP (ie. you're connecting from the same computer), the
- # connection is considered secure and plaintext authentication is allowed.
- #disable_plaintext_auth = no
- # Should all IMAP and POP3 processes be killed when Dovecot master process
- # shuts down. Setting this to "no" means that Dovecot can be upgraded without
- # forcing existing client connections to close (although that could also be
- # a problem if the upgrade is eg. because of a security fix). This however
- # means that after master process has died, the client processes can't write
- # to log files anymore.
- #shutdown_clients = yes
- ##
- ## Logging
- ##
- # Use this logfile instead of syslog(). /dev/stderr can be used if you want to
- # use stderr for logging (ONLY /dev/stderr - otherwise it is closed).
- #log_path =
- # For informational messages, use this logfile instead of the default
- #info_log_path =
- # Prefix for each line written to log file. % codes are in strftime(3)
- # format.
- #log_timestamp = "%b %d %H:%M:%S "
- # Syslog facility to use if you're logging to syslog. Usually if you don't
- # want to use "mail", you'll use local0..local7. Also other standard
- # facilities are supported.
- #syslog_facility = mail
- ##
- ## SSL settings
- ##
- # IP or host address where to listen in for SSL connections. Defaults
- # to above if not specified.
- #ssl_listen =
- ssl_listen = ton.adresse.ip.ici
- # Disable SSL/TLS support.
- ssl_disable = no
- # PEM encoded X.509 SSL/TLS certificate and private key. They're opened before
- # dropping root privileges, so keep the key file unreadable by anyone but
- # root. Included doc/mkcert.sh can be used to easily generate self-signed
- # certificate, just make sure to update the domains in dovecot-openssl.cnf
- #ssl_cert_file = /etc/pki/dovecot/certs/dovecot.pem
- #ssl_key_file = /etc/pki/dovecot/private/dovecot.pem
- ssl_cert_file = /etc/myshop/cacert.pem
- ssl_key_file = /etc/myshop/private/cakey.pem
- # If key file is password protected, give the password here. Alternatively
- # give it when starting dovecot with -p parameter.
- ssl_key_password = wn1PW4OP
- # File containing trusted SSL certificate authorities. Usually not needed.
- # The CAfile should contain the CA-certificate(s) followed by the matching
- # CRL(s). CRL checking is new in dovecot .rc1
- #ssl_ca_file =
- # Request client to send a certificate.
- #ssl_verify_client_cert = no
- # How often to regenerate the SSL parameters file. Generation is quite CPU
- # intensive operation. The value is in hours, 0 disables regeneration
- # entirely.
- #ssl_parameters_regenerate = 168
- # SSL ciphers to use
- #ssl_cipher_list = ALL:!LOW
- # Show protocol level SSL errors.
- #verbose_ssl = no
- ##
- ## Login processes
- ##
- # Directory where authentication process places authentication UNIX sockets
- # which login needs to be able to connect to. The sockets are created when
- # running as root, so you don't have to worry about permissions. Note that
- # everything in this directory is deleted when Dovecot is started.
- #login_dir = /var/run/dovecot/login
- # chroot login process to the login_dir. Only reason not to do this is if you
- # wish to run the whole Dovecot without roots.
- # http://wiki.dovecot.org/Rootless
- #login_chroot = yes
- # User to use for the login process. Create a completely new user for this,
- # and don't use it anywhere else. The user must also belong to a group where
- # only it has access, it's used to control access for authentication process.
- # Note that this user is NOT used to access mails.
- # http://wiki.dovecot.org/UserIds
- #login_user = dovecot
- # Set max. process size in megabytes. If you don't use
- # login_process_per_connection you might need to grow this.
- #login_process_size = 32
- # Should each login be processed in it's own process (yes), or should one
- # login process be allowed to process multiple connections (no)? Yes is more
- # secure, espcially with SSL/TLS enabled. No is faster since there's no need
- # to create processes all the time.
- #login_process_per_connection = yes
- # Number of login processes to keep for listening new connections.
- #login_processes_count = 3
- # Maximum number of login processes to create. The listening process count
- # usually stays at login_processes_count, but when multiple users start logging
- # in at the same time more extra processes are created. To prevent fork-bombing
- # we check only once in a second if new processes should be created - if all
- # of them are used at the time, we double their amount until the limit set by
- # this setting is reached.
- #login_max_processes_count = 128
- # Maximum number of connections allowed per each login process. This setting
- # is used only if login_process_per_connection=no. Once the limit is reached,
- # the process notifies master so that it can create a new login process.
- # You should make sure that the process has at least
- # 16 + login_max_connections * 2 available file descriptors.
- #login_max_connections = 256
- # Greeting message for clients.
- #login_greeting = Dovecot ready.
- # Space-separated list of elements we want to log. The elements which have
- # a non-empty variable value are joined together to form a comma-separated
- # string.
- #login_log_format_elements = user=<%u> method=%m rip=%r lip=%l %c
- # Login log format. %$ contains login_log_format_elements string, %s contains
- # the data we want to log.
- #login_log_format = %$: %s
- ##
- ## Mailbox locations and namespaces
- ##
- # Location for users' mailboxes. This is the same as the old default_mail_env
- # setting. The default is empty, which means that Dovecot tries to find the
- # mailboxes automatically. This won't work if the user doesn't have any mail
- # yet, so you should explicitly tell Dovecot the full location.
- #
- # If you're using mbox, giving a path to the INBOX file (eg. /var/mail/%u)
- # isn't enough. You'll also need to tell Dovecot where the other mailboxes are
- # and where Dovecot can place its index files. This is called the "root mail
- # directory", and it must be the first path given in the mail_location setting.
- #
- # There are a few special variables you can use, eg.:
- #
- # %u - username
- # %n - user part in user@domain, same as %u if there's no domain
- # %d - domain part in user@domain, empty if there's no domain
- # %h - home directory
- #
- # See doc/variables.txt for full list. Some examples:
- #
- # mail_location = maildir:~/Maildir
- # mail_location = mbox:~/mail:INBOX=/var/mail/%u
- # mail_location = mbox:/var/mail/%d/%1n/%n:INDEX=/var/indexes/%d/%1n/%n
- #
- # http://wiki.dovecot.org/MailLocation
- #
- #mail_location =
- # If you need to set multiple mailbox locations or want to change default
- # namespace settings, you can do it by defining namespace sections:
- #
- # You can have private, shared and public namespaces. The only difference
- # between them is how Dovecot announces them to client via NAMESPACE
- # extension. Shared namespaces are meant for user-owned mailboxes which are
- # shared to other users, while public namespaces are for more globally
- # accessible mailboxes.
- #
- # REMEMBER: If you add any namespaces, the default namespace must be added
- # explicitly, ie. mail_location does nothing unless you have a namespace
- # without a location setting. Default namespace is simply done by having a
- # namespace with empty prefix.
- #namespace private {
- # Hierarchy separator to use. You should use the same separator for all
- # namespaces or some clients get confused. '/' is usually a good one.
- # The default however depends on the underlying mail storage format.
- #separator =
- # Prefix required to access this namespace. This needs to be different for
- # all namespaces. For example "Public/".
- #prefix =
- # Physical location of the mailbox. This is in same format as
- # mail_location, which is also the default for it.
- #location =
- # There can be only one INBOX, and this setting defines which namespace
- # has it.
- #inbox = yes
- # If namespace is hidden, it's not advertised to clients via NAMESPACE
- # extension or shown in LIST replies. This is mostly useful when converting
- # from another server with different namespaces which you want to depricate
- # but still keep working. For example you can create hidden namespaces with
- # prefixes "~/mail/", "~%u/mail/" and "mail/".
- #hidden = yes
- #}
- # Grant access to these extra groups for mail processes. Typical use would be
- # to give "mail" group write access to /var/mail to be able to create dotlocks.
- #mail_extra_groups =
- # Allow full filesystem access to clients. There's no access checks other than
- # what the operating system does for the active UID/GID. It works with both
- # maildir and mboxes, allowing you to prefix mailboxes names with eg. /path/
- # or ~user/.
- #mail_full_filesystem_access = no
- ##
- ## Mail processes
- ##
- # Enable mail process debugging. This can help you figure out why Dovecot
- # isn't finding your mails.
- #mail_debug = no
- # Log prefix for mail processes. See doc/variables.txt for list of possible
- # variables you can use.
- #mail_log_prefix = "%Us(%u): "
- # Use mmap() instead of read() to read mail files. read() seems to be a bit
- # faster with my Linux/x86 and it's better with NFS, so that's the default.
- # Note that OpenBSD 3.3 and older don't work right with mail_read_mmaped = yes.
- #mail_read_mmaped = no
- # Don't use mmap() at all. This is required if you store indexes to shared
- # filesystems (NFS or clustered filesystem).
- #mmap_disable = no
- # Don't write() to mmaped files. This is required for some operating systems
- # which use separate caches for them, such as OpenBSD.
- #mmap_no_write = no
- # Locking method for index files. Alternatives are fcntl, flock and dotlock.
- # Dotlocking uses some tricks which may create more disk I/O than other locking
- # methods. NOTE: If you use NFS, remember to change also mmap_disable setting!
- #lock_method = fcntl
- # Drop all privileges before exec()ing the mail process. This is mostly
- # meant for debugging, otherwise you don't get core dumps. It could be a small
- # security risk if you use single UID for multiple users, as the users could
- # ptrace() each others processes then.
- #mail_drop_priv_before_exec = no
- # Show more verbose process titles (in ps). Currently shows user name and
- # IP address. Useful for seeing who are actually using the IMAP processes
- # (eg. shared mailboxes or if same uid is used for multiple accounts).
- #verbose_proctitle = no
- # Valid UID range for users, defaults to 500 and above. This is mostly
- # to make sure that users can't log in as daemons or other system users.
- # Note that denying root logins is hardcoded to dovecot binary and can't
- # be done even if first_valid_uid is set to 0.
- #first_valid_uid = 500
- #last_valid_uid = 0
- # Valid GID range for users, defaults to non-root/wheel. Users having
- # non-valid GID as primary group ID aren't allowed to log in. If user
- # belongs to supplementary groups with non-valid GIDs, those groups are
- # not set.
- #first_valid_gid = 1
- #last_valid_gid = 0
- # Maximum number of running mail processes. When this limit is reached,
- # new users aren't allowed to log in.
- #max_mail_processes = 1024
- # Set max. process size in megabytes. Most of the memory goes to mmap()ing
- # files, so it shouldn't harm much even if this limit is set pretty high.
- #mail_process_size = 256
- # Maximum allowed length for mail keyword name. It's only forced when trying
- # to create new keywords.
- #mail_max_keyword_length = 50
- # Default umask to use for mail files and directories.
- #umask = 0077
- # ':' separated list of directories under which chrooting is allowed for mail
- # processes (ie. /var/mail will allow chrooting to /var/mail/foo/bar too).
- # This setting doesn't affect login_chroot or auth_chroot variables.
- # WARNING: Never add directories here which local users can modify, that
- # may lead to root exploit. Usually this should be done only if you don't
- # allow shell access for users. See doc/configuration.txt for more information.
- #valid_chroot_dirs =
- # Default chroot directory for mail processes. This can be overridden for
- # specific users in user database by giving /./ in user's home directory
- # (eg. /home/./user chroots into /home). Note that usually there is no real
- # need to do chrooting, Dovecot doesn't allow users to access files outside
- # their mail directory anyway.
- #mail_chroot =
- ##
- ## Mailbox handling optimizations
- ##
- # Space-separated list of fields to initially save into cache file. Currently
- # these fields are allowed:
- #
- # flags, date.sent, date.received, size.virtual, size.physical
- # mime.parts, imap.body, imap.bodystructure
- #
- # Different IMAP clients work in different ways, so they benefit from
- # different cached fields. Some do not benefit from them at all. Caching more
- # than necessary generates useless disk I/O, so you don't want to do that
- # either.
- #
- # Dovecot attempts to automatically figure out what client wants and it keeps
- # only that. However the first few times a mailbox is opened, Dovecot hasn't
- # yet figured out what client needs, so it may not perform optimally. If you
- # know what fields the majority of your clients need, it may be useful to set
- # these fields by hand. If client doesn't actually use them, Dovecot will
- # eventually drop them.
- #
- # Usually you should just leave this field alone. The potential benefits are
- # typically unnoticeable.
- #mail_cache_fields =
- # Space-separated list of fields that Dovecot should never save to cache file.
- # Useful if you want to save disk space at the cost of more I/O when the fields
- # needed.
- #mail_never_cache_fields =
- # The minimum number of mails in a mailbox before updates are done to cache
- # file. This allows optimizing Dovecot's behavior to do less disk writes at
- # the cost of more disk reads.
- #mail_cache_min_mail_count = 0
- # When IDLE command is running, mailbox is checked once in a while to see if
- # there are any new mails or other changes. This setting defines the minimum
- # time to wait between those checks. Dovecot is however able to use dnotify
- # and inotify with Linux to reply immediately after the change occurs.
- #mailbox_idle_check_interval = 30
- # Save mails with CR+LF instead of plain LF. This makes sending those mails
- # take less CPU, especially with sendfile() syscall with Linux and FreeBSD.
- # But it also creates a bit more disk I/O which may just make it slower.
- # Also note that if other software reads the mboxes/maildirs, they may handle
- # the extra CRs wrong and cause problems.
- #mail_save_crlf = no
- ##
- ## Maildir-specific settings
- ##
- # By default LIST command returns all entries in maildir beginning with dot.
- # Enabling this option makes Dovecot return only entries which are directories.
- # This is done by stat()ing each entry, so it causes more disk I/O.
- # (For systems setting struct dirent->d_type, this check is free and it's
- # done always regardless of this setting)
- #maildir_stat_dirs = no
- # Copy mail to another folders using hard links. This is much faster than
- # actually copying the file. This is problematic only if something modifies
- # the mail in one folder but doesn't want it modified in the others. I don't
- # know any MUA which would modify mail files directly. IMAP protocol also
- # requires that the mails don't change, so it would be problematic in any case.
- # If you care about performance, enable it.
- #maildir_copy_with_hardlinks = no
- ##
- ## mbox-specific settings
- ##
- # Which locking methods to use for locking mbox. There are four available:
- # dotlock: Create <mailbox>.lock file. This is the oldest and most NFS-safe
- # solution. If you want to use /var/mail/ like directory, the users
- # will need write access to that directory.
- # fcntl : Use this if possible. Works with NFS too if lockd is used.
- # flock : May not exist in all systems. Doesn't work with NFS.
- # lockf : May not exist in all systems. Doesn't work with NFS.
- #
- # You can use multiple locking methods; if you do the order they're declared
- # in is important to avoid deadlocks if other MTAs/MUAs are using multiple
- # locking methods as well. Some operating systems don't allow using some of
- # them simultaneously.
- #mbox_read_locks = fcntl
- #mbox_write_locks = fcntl
- # Maximum time in seconds to wait for lock (all of them) before aborting.
- #mbox_lock_timeout = 300
- # If dotlock exists but the mailbox isn't modified in any way, override the
- # lock file after this many seconds.
- #mbox_dotlock_change_timeout = 120
- # When mbox changes unexpectedly we have to fully read it to find out what
- # changed. If the mbox is large this can take a long time. Since the change
- # is usually just a newly appended mail, it'd be faster to simply read the
- # new mails. If this setting is enabled, Dovecot does this but still safely
- # fallbacks to re-reading the whole mbox file whenever something in mbox isn't
- # how it's expected to be. The only real downside to this setting is that if
- # some other MUA changes message flags, Dovecot doesn't notice it immediately.
- # Note that a full sync is done with SELECT, EXAMINE, EXPUNGE and CHECK
- # commands.
- #mbox_dirty_syncs = yes
- # Like mbox_dirty_syncs, but don't do full syncs even with SELECT, EXAMINE,
- # EXPUNGE or CHECK commands. If this is set, mbox_dirty_syncs is ignored.
- #mbox_very_dirty_syncs = no
- # Delay writing mbox headers until doing a full write sync (EXPUNGE and CHECK
- # commands and when closing the mailbox). This is especially useful for POP3
- # where clients often delete all mails. The downside is that our changes
- # aren't immediately visible to other MUAs.
- #mbox_lazy_writes = yes
- # If mbox size is smaller than this (in kilobytes), don't write index files.
- # If an index file already exists it's still read, just not updated.
- #mbox_min_index_size = 0
- ##
- ## dbox-specific settings
- ##
- # Maximum dbox file size in kilobytes until it's rotated.
- #dbox_rotate_size = 2048
- # Minimum dbox file size in kilobytes before it's rotated
- # (overrides dbox_rotate_days)
- #dbox_rotate_min_size = 16
- # Maximum dbox file age in days until it's rotated. Day always begins from
- # midnight, so 1 = today, 2 = yesterday, etc. 0 = check disabled.
- #dbox_rotate_days = 0
- ##
- ## IMAP specific settings
- ##
- protocol imap {
- # Login executable location.
- #login_executable = /usr/libexec/dovecot/imap-login
- # IMAP executable location. Changing this allows you to execute other
- # binaries before the imap process is executed.
- #
- # This would write rawlogs into ~/dovecot.rawlog/ directory:
- # mail_executable = /usr/libexec/dovecot/rawlog /usr/libexec/dovecot/imap
- #
- # This would attach gdb into the imap process and write backtraces into
- # /tmp/gdbhelper.* files:
- # mail_executable = /usr/libexec/dovecot/gdbhelper /usr/libexec/dovecot/imap
- #
- #mail_executable = /usr/libexec/dovecot/imap
- # Maximum IMAP command line length in bytes. Some clients generate very long
- # command lines with huge mailboxes, so you may need to raise this if you get
- # "Too long argument" or "IMAP command line too large" errors often.
- #imap_max_line_length = 65536
- # Support for dynamically loadable plugins. mail_plugins is a space separated
- # list of plugins to load.
- #mail_plugins =
- #mail_plugin_dir = /usr/lib/dovecot/imap
- # Send IMAP capabilities in greeting message. This makes it unnecessary for
- # clients to request it with CAPABILITY command, so it saves one round-trip.
- # Many clients however don't understand it and ask the CAPABILITY anyway.
- #login_greeting_capability = no
- # Override the IMAP CAPABILITY response.
- #imap_capability =
- # Workarounds for various client bugs:
- # delay-newmail:
- # Send EXISTS/RECENT new mail notifications only when replying to NOOP
- # and CHECK commands. Some clients ignore them otherwise, for example
- # OSX Mail. Outlook Express breaks more badly though, without this it
- # may show user "Message no longer in server" errors. Note that OE6 still
- # breaks even with this workaround if synchronization is set to
- # "Headers Only".
- # outlook-idle:
- # Outlook and Outlook Express never abort IDLE command, so if no mail
- # arrives in half a hour, Dovecot closes the connection. This is still
- # fine, except Outlook doesn't connect back so you don't see if new mail
- # arrives.
- # netscape-eoh:
- # Netscape 4.x breaks if message headers don't end with the empty "end of
- # headers" line. Normally all messages have this, but setting this
- # workaround makes sure that Netscape never breaks by adding the line if
- # it doesn't exist. This is done only for FETCH BODY[HEADER.FIELDS..]
- # commands. Note that RFC says this shouldn't be done.
- # tb-extra-mailbox-sep:
- # With mbox storage a mailbox can contain either mails or submailboxes,
- # but not both. Thunderbird separates these two by forcing server to
- # accept '/' suffix in mailbox names in subscriptions list.
- # The list is space-separated.
- #imap_client_workarounds = outlook-idle
- }
-
- ##
- ## POP3 specific settings
- ##
- protocol pop3 {
- # Login executable location.
- #login_executable = /usr/libexec/dovecot/pop3-login
- # POP3 executable location. See IMAP's mail_executable above for examples
- # how this could be changed.
- #mail_executable = /usr/libexec/dovecot/pop3
- # Don't try to set mails non-recent or seen with POP3 sessions. This is
- # mostly intended to reduce disk I/O. With maildir it doesn't move files
- # from new/ to cur/, with mbox it doesn't write Status-header.
- #pop3_no_flag_updates = no
- # Support LAST command which exists in old POP3 specs, but has been removed
- # from new ones. Some clients still wish to use this though. Enabling this
- # makes RSET command clear all \Seen flags from messages.
- #pop3_enable_last = no
- # If mail has X-UIDL header, use it as the mail's UIDL.
- #pop3_reuse_xuidl = no
- # Keep the mailbox locked for the entire POP3 session.
- #pop3_lock_session = no
- # POP3 UIDL format to use. You can use following variables:
- #
- # %v - Mailbox UIDVALIDITY
- # %u - Mail UID
- # %m - MD5 sum of the mailbox headers in hex (mbox only)
- # %f - filename (maildir only)
- #
- # If you want UIDL compatibility with other POP3 servers, use:
- # UW's ipop3d : %08Xv%08Xu
- # Courier version 0 : %f
- # Courier version 1 : %u
- # Courier version 2 : %v-%u
- # Cyrus (<= 2.1.3) : %u
- # Cyrus (>= 2.1.4) : %v.%u
- # Older Dovecots : %v.%u
- # tpop3d : %Mf
- #
- # Note that Outlook 2003 seems to have problems with %v.%u format which was
- # Dovecot's default, so if you're building a new server it would be a good
- # idea to change this. %08Xu%08Xv should be pretty fail-safe.
- #
- # NOTE: Nowadays this is required to be set explicitly, since the old
- # default was bad but it couldn't be changed without breaking existing
- # installations. %08Xu%08Xv will be the new default, so use it for new
- # installations.
- #
- #pop3_uidl_format = %08Xu%08Xv
- pop3_uidl_format = %v.%u
- # POP3 logout format string:
- # %t - number of TOP commands
- # %p - number of bytes sent to client as a result of TOP command
- # %r - number of RETR commands
- # %b - number of bytes sent to client as a result of RETR command
- # %d - number of deleted messages
- # %m - number of messages (before deletion)
- # %s - mailbox size in bytes (before deletion)
- #pop3_logout_format = top=%t/%p, retr=%r/%b, del=%d/%m, size=%s
- # Support for dynamically loadable plugins. mail_plugins is a space separated
- # list of plugins to load.
- #mail_plugins =
- #mail_plugin_dir = /usr/lib/dovecot/pop3
- # Workarounds for various client bugs:
- # outlook-no-nuls:
- # Outlook and Outlook Express hang if mails contain NUL characters.
- # This setting replaces them with 0x80 character.
- # oe-ns-eoh:
- # Outlook Express and Netscape Mail breaks if end of headers-line is
- # missing. This option simply sends it if it's missing.
- # The list is space-separated.
- #pop3_client_workarounds =
- }
- ##
- ## LDA specific settings
- ##
- protocol lda {
- # Address to use when sending rejection mails.
- postmaster_address = postmaster@example.com
- # Hostname to use in various parts of sent mails, eg. in Message-Id.
- # Default is the system's real hostname.
- #hostname =
- # Support for dynamically loadable plugins. mail_plugins is a space separated
- # list of plugins to load.
- #mail_plugins =
- #mail_plugin_dir = /usr/lib/dovecot/lda
- # Binary to use for sending mails.
- #sendmail_path = /usr/lib/sendmail
- # UNIX socket path to master authentication server to find users.
- #auth_socket_path = /var/run/dovecot/auth-master
- }
- ##
- ## Authentication processes
- ##
- # Executable location
- #auth_executable = /usr/libexec/dovecot/dovecot-auth
- # Set max. process size in megabytes.
- #auth_process_size = 256
- # Authentication cache size in kilobytes. 0 means it's disabled.
- # Note that bsdauth, PAM and vpopmail require cache_key to be set for caching
- # to be used. Also note that currently auth cache doesn't work very well if
- # you're using multiple passdbs with same usernames in them.
- #auth_cache_size = 0
- # Time to live in seconds for cached data. After this many seconds the cached
- # record is no longer used, *except* if the main database lookup returns
- # internal failure. We also try to handle password changes automatically: If
- # user's previous authentication was successful, but this one wasn't, the
- # cache isn't used. For now this works only with plaintext authentication.
- #auth_cache_ttl = 3600
- # Space separated list of realms for SASL authentication mechanisms that need
- # them. You can leave it empty if you don't want to support multiple realms.
- # Many clients simply use the first one listed here, so keep the default realm
- # first.
- #auth_realms =
- # Default realm/domain to use if none was specified. This is used for both
- # SASL realms and appending @domain to username in plaintext logins.
- #auth_default_realm =
- # List of allowed characters in username. If the user-given username contains
- # a character not listed in here, the login automatically fails. This is just
- # an extra check to make sure user can't exploit any potential quote escaping
- # vulnerabilities with SQL/LDAP databases. If you want to allow all characters,
- # set this value to empty.
- #auth_username_chars = abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ01234567890.-_@
- # Username character translations before it's looked up from databases. The
- # value contains series of from -> to characters. For example "#@/@" means
- # that '#' and '/' characters are translated to '@'.
- #auth_username_translation =
- # Username formatting before it's looked up from databases. You can use
- # the standard variables here, eg. %Lu would lowercase the username, %n would
- # drop away the domain if it was given, or "%n-AT-%d" would change the '@' into
- # "-AT-". This translation is done after auth_username_translation changes.
- #auth_username_format =
- # If you want to allow master users to log in by specifying the master
- # username within the normal username string (ie. not using SASL mechanism's
- # support for it), you can specify the separator character here. The format
- # is then <username><separator><master username>. UW-IMAP uses "*" as the
- # separator, so that could be a good choice.
- #auth_master_user_separator =
- # Username to use for users logging in with ANONYMOUS SASL mechanism
- #auth_anonymous_username = anonymous
- # More verbose logging. Useful for figuring out why authentication isn't
- # working.
- #auth_verbose = no
- # Even more verbose logging for debugging purposes. Shows for example SQL
- # queries.
- #auth_debug = no
- # In case of password mismatches, log the passwords and used scheme so the
- # problem can be debugged. Requires auth_debug=yes to be set.
- #auth_debug_passwords = no
- # Maximum number of dovecot-auth worker processes. They're used to execute
- # blocking passdb and userdb queries (eg. MySQL and PAM). They're
- # automatically created and destroyed as needed.
- #auth_worker_max_count = 30
- # Kerberos keytab to use for the GSSAPI mechanism. Will use the system
- # default (usually /etc/krb5.keytab) if not specified.
- #auth_krb5_keytab =
- auth default {
- # Space separated list of wanted authentication mechanisms:
- # plain login digest-md5 cram-md5 ntlm rpa apop anonymous gssapi
- mechanisms = plain
- # Users can be temporarily disabled by adding a passdb with deny=yes.
- # If the user is found from that database, authentication will fail.
- # The deny passdb should always be specified before others, so it gets
- # checked first. Here's an example:
- #passdb passwd-file {
- # File contains a list of usernames, one per line
- #args = /etc/dovecot.deny
- #deny = yes
- #}
- # PAM authentication. Preferred nowadays by most systems.
- # Note that PAM can only be used to verify if user's password is correct,
- # so it can't be used as userdb. If you don't want to use a separate user
- # database (passwd usually), you can use static userdb.
- # REMEMBER: You'll need /etc/pam.d/dovecot file created for PAM
- # authentication to actually work.
- # http://wiki.dovecot.org/PasswordDatabase/PAM
- passdb pam {
- }
- # /etc/passwd or similar, using getpwnam()
- # In many systems nowadays this uses Name Service Switch, which is
- # configured in /etc/nsswitch.conf.
- # http://wiki.dovecot.org/AuthDatabase/Passwd
- #passdb passwd {
- #}
- # /etc/shadow or similiar, using getspnam(). Deprecated by PAM nowadays.
- # http://wiki.dovecot.org/PasswordDatabase/Shadow
- #passdb shadow {
- #}
- # PAM-like authentication for OpenBSD.
- # http://wiki.dovecot.org/PasswordDatabase/BSDAuth
- #passdb bsdauth {
- # [cache_key=<key>] - See cache_key in PAM for explanation.
- #args =
- #}
- # passwd-like file with specified location
- # http://wiki.dovecot.org/AuthDatabase/PasswdFile
- #passdb passwd-file {
- # Path for passwd-file
- #args =
- #}
- # checkpassword executable authentication
- # NOTE: You will probably want to use "userdb prefetch" with this.
- # http://wiki.dovecot.org/PasswordDatabase/CheckPassword
- #passdb checkpassword {
- # Path for checkpassword binary
- #args =
- #}
- # SQL database
- # http://wiki.dovecot.org/AuthDatabase/SQL
- #passdb sql {
- # Path for SQL configuration file, see doc/dovecot-sql.conf for example
- #args =
- #}
- # LDAP database
- # http://wiki.dovecot.org/AuthDatabase/LDAP
- #passdb ldap {
- # Path for LDAP configuration file, see doc/dovecot-ldap.conf for example
- #args =
- #}
- # vpopmail authentication
- # http://wiki.dovecot.org/AuthDatabase/VPopMail
- #passdb vpopmail {
- # [cache_key=<key>] - See cache_key in PAM for explanation.
- #args =
- #}
- # /etc/passwd or similar, using getpwnam()
- # In many systems nowadays this uses Name Service Switch, which is
- # configured in /etc/nsswitch.conf. WARNING: nss_ldap is known to be broken
- # with Dovecot. Don't use it, or users might log in as each others!
- # http://wiki.dovecot.org/AuthDatabase/Passwd
- userdb passwd {
- }
- # passwd-like file with specified location
- # http://wiki.dovecot.org/AuthDatabase/PasswdFile
- #userdb passwd-file {
- # Path for passwd-file
- #args =
- #}
- # static settings generated from template
- # http://wiki.dovecot.org/UserDatabase/Static
- #userdb static {
- # Template for the fields. Can return anything a userdb could normally
- # return. For example:
- #
- # args = uid=500 gid=500 home=/var/mail/%u
- #
- #args =
- #}
- # SQL database
- # http://wiki.dovecot.org/AuthDatabase/SQL
- #userdb sql {
- # Path for SQL configuration file, see doc/dovecot-sql.conf for example
- #args =
- #}
- # LDAP database
- # http://wiki.dovecot.org/AuthDatabase/LDAP
- #userdb ldap {
- # Path for LDAP configuration file, see doc/dovecot-ldap.conf for example
- #args =
- #}
- # vpopmail
- # http://wiki.dovecot.org/AuthDatabase/VPopMail
- #userdb vpopmail {
- #}
- # "prefetch" user database means that the passdb already provided the
- # needed information and there's no need to do a separate userdb lookup.
- # This can be made to work with SQL and LDAP databases, see their example
- # configuration files for more information how to do it.
- # http://wiki.dovecot.org/UserDatabase/Prefetch
- #userdb prefetch {
- #}
- # User to use for the process. This user needs access to only user and
- # password databases, nothing else. Only shadow and pam authentication
- # requires roots, so use something else if possible. Note that passwd
- # authentication with BSDs internally accesses shadow files, which also
- # requires roots. Note that this user is NOT used to access mails.
- # That user is specified by userdb above.
- user = root
- # It's possible to export the authentication interface to other programs:
- #socket listen {
- #master {
- # Master socket is typically used to give Dovecot's local delivery
- # agent access to userdb so it can find mailbox locations. It can
- # however also be used to disturb regular user authentications.
- # WARNING: Giving untrusted users access to master socket may be a
- # security risk, don't give too wide permissions to it!
- #path = /var/run/dovecot/auth-master
- #mode = 0600
- # Default user/group is the one who started dovecot-auth (root)
- #user =
- #group =
- #}
- #client {
- # The client socket is generally safe to export to everyone. Typical use
- # is to export it to your SMTP server so it can do SMTP AUTH lookups
- # using it.
- #path = /var/run/dovecot/auth-client
- #mode = 0660
- #}
- #}
- }
- # If you wish to use another authentication server than dovecot-auth, you can
- # use connect sockets. They assumed to be already running, Dovecot's master
- # process only tries to connect to them. They don't need any other settings
- # than the path for the master socket, as the configuration is done elsewhere.
- # Note that the client sockets must exist in the login_dir.
- #auth external {
- # socket connect {
- # master {
- # path = /var/run/dovecot/auth-master
- # }
- # }
- #}
- ##
- ## Dictionary server settings
- ##
- # Dictionary can be used by some plugins to store key=value lists.
- # Currently this is only used by dict quota backend. The dictionary can be
- # used either directly or though a dictionary server. The following dict block
- # maps dictionary names to URIs when the server is used. These can then be
- # referenced using URIs in format "proxy:<name>".
- dict {
- #quota = mysql:/etc/dovecot-dict-quota.conf
- }
- ##
- ## Plugin settings
- ##
- plugin {
- # Here you can give some extra environment variables to mail processes.
- # This is mostly meant for passing parameters to plugins. %variable
- # expansion is done for all values.
- # Convert plugin. If set, specifies the source storage path which is
- # converted to destination storage (mail_location).
- #convert_mail = mbox:%h/mail
- # Trash plugin. When saving a message would make user go over quota, this
- # plugin automatically deletes the oldest mails from configured mailboxes
- # until the message can be saved within quota limits. The configuration file
- # is a text file where each line is in format: <priority> <mailbox name>
- # Mails are first deleted in lowest -> highest priority number order
- #trash = /etc/dovecot-trash.conf
- }
- protocols = imaps
|
Message édité par Charly303 le 13-06-2007 à 20:38:31
|
etc/dovecot-dict-quota.conf