resolution graphique sous sarge

Recherche :

Mot : Pseudo : Filtrer
Bas de page
Auteur	Sujet : resolution graphique sous sarge

R4GTL

Ca yé je vient d'installer la Sarge.
Ma carte graphique a bien été detecté (ati 8500).
J'ai configuré manuellement les spécificités de l'ecran (resolutions verticale et horizontale), lors de l'installation.
Mais au premier démarrage, la surprise. Je n'ai le choix de resolution qu'entre le 640*480 et le 800*600, alors que je souhaite le 1200*1024.
J'ai un peu fouillé, mais je n'ai rien trouvé.
Surtout que je suis plutot habituer aux distributions Mandrake ou RedHat (rha l'habitude de la facilité).
Alors, si yen a qui peuvent me donner un coup de main, sinon, ba je remet une fedora ou mandriva (d'ailleurs faudrai que j'essai la derniere), et j'abandonne définitivement la Débian qui n'est pas fichue de me proposer autre chose que du 800*600

Publicité

Nelyot Tchagui

ce genre de réaction ne donne pas vraiment envie de t'aider
personne ne t'oblige à utiliser debian,

pour ton problème, les résolutions peuvent se régler dans le fichier /etc/X11/XF86config-4
dans la section screen tu ajoutes à la main les résolutions que tu souhaites,

il y a encore un autre moyen plus simple, c'est de lancer
dpkg-reconfigure xserver-xfree86, et là tu coches toutes les résolutions qui t'intéresse

Nelyot Tchagui

bien sûr pour s'en rendre compte il faut redémmarrer le serveur graphique,

par exemple avec /etc/init.d/gdm restart

R4GTL

désolé pour le ton de ma question, mais je recherchais depuis une heure comment modifier la resolution, qui ne s'etait pas fait automatiquement. Et comme Débian ne se configure pas de la meme facon que Mandrake et Fédora, j'ai vite été dépassé.

En tout cas, merci pour ta reponse rapide et precise.

el cabron

me gusta el perico

j ai exactement le meme probleme (meme carte graphique)que R4GTL (probleme de newbies certainement)
le pilote installé par defaut est un generique, et l on ne peut effectivement pas depasser 800x600.modifier la resolution dans le fichier "XF86config-4" n y change rien.
j ai donc installé les pilotes ( https://support.ati.com/ics/support [...] ionID=3380 ) idoines.malheureusement apres l installation ("auto","custom" ou "Generate Distribution Specific Driver Package" ) serverx ne demarre plus.
avec "dpkg-reconfigure xserver-xfree86" j ai testé differentes combinaisons sans resultat.la seule solution a chaque fois et de renommer "XF86config-4.old" en "XF86config-4" pour pouvoir redemarrer serverx.

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

Nelyot Tchagui

poste le résultat de la commande:
cat /etc/X11XF86config-4.old

el cabron

me gusta el perico

cette commande ne passe pas (meme en la modifiant en "cat: /etc/X11/XF86Config-4.old" j obtiens : Aucun fichier ou répertoire de ce type
pcdebian:~#
je l a tape ou et comment ?

Nelyot Tchagui

la commande c'est

Code :

cat /etc/X11/XF86Config-4.old

ou si tu as Xorg comme serveur graphique

Code :

cat /etc/X11/xorg.conf~

Message édité par Nelyot Tchagui le 14-06-2005 à 09:45:25

goldpegaz

J'ai eu le même probleme au demarrage de ma debian ..

mais un : dpkg-reconfigure xserver-xfree86 et un restart m'a permis de resoudre le probleme.

el cabron

me gusta el perico

Nelyot Tchagui a écrit :

la commande c'est

Code :

cat /etc/X11/XF86Config-4.old

[/cpp]

passe pas, dois la taper au reboot lorsque xserver ne veux pas demarrer ?

goldpegaz a écrit :

J'ai eu le même probleme au demarrage de ma debian ..

mais un : dpkg-reconfigure xserver-xfree86 et un restart m'a permis de resoudre le probleme.

veux rien savoir chez moi :cry: (alors que tout semble bien se passer et meme en selectionnant VGA a la place d ATI )
je me demande si ce n est pas un probleme avec mon ecran (LCD)

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

Publicité

korben31

C'est sure qu'une reaction comme ca ...
Debian je trouve que c'est une des meilleur distri mais bon faut etre patient et c'est sure c'est pas pour les noob qui sorte de mandrake ... c'est le jours et la nuit

Nelyot Tchagui

passe pas?
tu lances ça dans une console hein? ton serveur graphique était censé marché en 800*600, non? au pire, démarre directement en mode console

el cabron

me gusta el perico

korben31 a écrit :

moi aussi j aime les frites, mais encore ?

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

zanton

disons que c'est différent : si tu veux n'avoir rien à faire et que tout soit configuré tout seul, en effet, c'est le jour et la nuit. Si tu es motivé et que tu as envie de comprendre comment ça fonctionne, même un débutant y arrivera, c'est juste une question d'envie. Dans le cas ici, je crois qu'effectivement, ce sont des débutants (ne pas savoir se servir de la console).

Sinon, avec les drivers génériques par défaut, on peut parfaitement avoir une résolution de 1280*1024 (et c'est bien 1280 pas 1200), c'est ce que j'ai au boulot et chez moi. Votre Sarge, vous l'avez installée avec quel environnement graphique ? (Gnome, KDE, etc). Vous embêtez pas pour le moment avec les drivers proprio.

Pour le cat et le dpkg-reconfigure, c'est juste après que tu te sois loggé, dans la console (après le signe # ou $). Si tu t'es connecté en root (superutilisateur), c'est # et tu as tous les droits sur ton système et c'est nécessaire pour effectuer dpkg-reconfigure et si tu t'es loggé en simple utilisateur, symbole $, tu ne pourras effectuer que le cat. Il nous faut vraiment le contenu du fichier pour pouvoir savoir ce qui ne va pas.

EDIT : je répondais à korben31 au départ

Message édité par zanton le 14-06-2005 à 10:16:56

korben31

cool t'es pas un peut belge carbon ?
Ah oui c'est sure moi a la base c'etait ca j'ai esseyer mandrake ( trop pas aimé ) RH ( pareil ) et debian j'ai accrocher de suite mais j'y es passé le temps... et now ca fait + de 2ans que j'utilise

el cabron

me gusta el perico

pour recentrer le debat, je n ai jamais dis que je voulais que cela se configure tout seul, si j avais choisis la facilité je serais resté sur XANDROS ou SUSE.
si je souhaite me mettre a DEBIAN c est uniquement pour mourir "un peu moins" con.
les quolibets ne me font pas vraiment avancé ..

pour en revenir au probleme, a force de bidouille je n ai plus de "XF86Config-4.old" (il faudrait peut etre que je reinstalle le pilote pour en generer un autre)
je peux mettre ici le "XF86Config-4" qui fait planter xserver mais il fait un km de long

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

korben31

normalement quand tu conf tes driver il conf xconfig avec...
surtout que les drivers ati je les encore install hier
tu fait chmod +x ati...run
./ati...run
et apres tu li... c'est pas bien dur

Nelyot Tchagui

vas-y post, on va pas te prier pendant des jours!

el cabron

me gusta el perico

korben31 a écrit :

normalement quand tu conf tes driver il conf xconfig avec...
surtout que les drivers ati je les encore install hier
tu fait chmod +x ati...run
./ati...run
et apres tu li... c'est pas bien dur

j ai utilisé la commande "./ati-driver-installer-8.14.13.run et tout semble bien se passer jusqu au reboot suivant (j ai suivie les instruction => http://www2.ati.com/drivers/linux/ [...] -inst.html

Nelyot Tchagui a écrit :

vas-y post, on va pas te prier pendant des jours!

# the rights to use, copy, modify, merge, publish, distribute, sublicense, # and/or sell copies of the Software, and to permit persons to whom the # Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in # all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR # IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, # FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL # THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, # WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF # OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE # SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall # not be used in advertising or otherwise to promote the sale, use or other # dealings in this Software without prior written authorization from the # XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of # this file.
# **********************************************************************

# **********************************************************************
# DRI Section
# **********************************************************************
Section "dri"
# Access to OpenGL ICD is allowed for all users:
Mode 0666
# Access to OpenGL ICD is restricted to a specific user group:
# Group 100 # users
# Mode 0660
EndSection

# **********************************************************************
# Module section -- this section is used to specify # which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
# Option "omit xfree86-dga"
EndSubSection

# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"

# This loads the GLX module
Load "glx" # libglx.a
Load "dri" # libdri.a

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set # **********************************************************************

Section "Files"

# The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db" ). There is normally # no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together), # as well as specifying multiple comma-separated entries in one FontPath # command (or a combination of both methods) # # If you don't have a floating point coprocessor and emacs, Mosaic or other # programs take long to start up, try moving the Type1 and Speedo directory # to the end of this list (or comment them out).
#

# FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"

# The module search path. The default path is shown here.

# ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging

# Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence # This allows clients to receive this key event.

# Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching # sequences. This allows clients to receive these key events.

# Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error.

# Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

# Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings.

# Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset).

# Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard" ).
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris), # uncomment the following line.

# Option "Protocol" "Xqueue"

Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"

# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and # control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""

# Option "XkbDisable"

Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "fr"

EndSection

# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "ExplorerPS/2"
Option "Device" "/dev/mouse"

# When using XQUEUE, comment out the above two lines, and uncomment # the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms)

Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection

# **********************************************************************
# Other input device sections
# this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"
Identifier "Monitor0"
HorizSync 31.5 - 108.5
VertRefresh 100 - 100
Option "DPMS"

# === Active Stereo mode lines based on GTF === # XVGA @ 100Hz Modeline "1024x768@100" 113.309 1024 1096 1208 1392 768 769 772 814 +hsync +vsync # XVGA @ 120Hz Modeline "1024x768@120" 139.054 1024 1104 1216 1408 768 769 772 823 +hsync +vsync # SXGA @ 100Hz Modeline "1280x1024@100" 190.960 1280 1376 1520 1760 1024 1025 1028 1085 +hsync +vsync # SXGA @ 120Hz Modeline "1280x1024@120" 233.793 1280 1384 1528 1776 1024 1025 1028 1097 +hsync +vsync

EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"

# The chipset line is optional in most cases. It can be used to override # the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver # modules, this line instructs the server to load the specified driver # module. Even when not using loadable driver modules, this line # indicates which driver should interpret the information in this section.

Driver "vga"
# The BusID line is used to specify which of possibly multiple devices # this section is intended for. When this line isn't present, a device # section can only match up with the primary video device. For PCI # devices a line like the following could be used. This line should not # normally be included unless there is more than one video device # installed.

# BusID "PCI:0:10:0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# === ATI device section ===

Section "Device"
Identifier "ATI Graphics Adapter"
Driver "fglrx"
# ### generic DRI settings ###
# === disable PnP Monitor ===
#Option "NoDDC"
# === disable/enable XAA/DRI ===
Option "no_accel" "no"
Option "no_dri" "no"
# === misc DRI settings ===
Option "mtrr" "off" # disable DRI mtrr mapper, driver has its own code for mtrr
# ### FireGL DDX driver module specific settings ### # === Screen Management ===
Option "DesktopSetup" "0x00000000"
Option "MonitorLayout" "CRT, CRT"
Option "IgnoreEDID" "off"
Option "HSync2" "unspecified"
Option "VRefresh2" "unspecified"
Option "ScreenOverlap" "0"
# === TV-out Management ===
Option "NoTV" "no"
Option "TVStandard" "PAL-H"
Option "TVHSizeAdj" "0"
Option "TVVSizeAdj" "0"
Option "TVHPosAdj" "0"
Option "TVVPosAdj" "0"
Option "TVHStartAdj" "0"
Option "TVColorAdj" "0"
Option "GammaCorrectionI" "0x00000000"
Option "GammaCorrectionII" "0x00000000"
# === OpenGL specific profiles/settings ===
Option "Capabilities" "0x00000800"
# === Video Overlay for the Xv extension ===
Option "VideoOverlay" "off"
# === OpenGL Overlay ===
# Note: When OpenGL Overlay is enabled, Video Overlay
# will be disabled automatically
Option "OpenGLOverlay" "off"
# === Center Mode (Laptops only) ===
Option "CenterMode" "off"
# === Pseudo Color Visuals (8-bit visuals) ===
Option "PseudoColorVisuals" "on"
# === QBS Management ===
Option "Stereo" "on"
Option "StereoSyncEnable" "1"
# === FSAA Management ===
Option "FSAAEnable" "yes"
Option "FSAAScale" "6"
Option "FSAADisableGamma" "no"
Option "FSAACustomizeMSPos" "no"
Option "FSAAMSPosX0" "0.000000"
Option "FSAAMSPosY0" "0.000000"
Option "FSAAMSPosX1" "0.000000"
Option "FSAAMSPosY1" "0.000000"
Option "FSAAMSPosX2" "0.000000"
Option "FSAAMSPosY2" "0.000000"
Option "FSAAMSPosX3" "0.000000"
Option "FSAAMSPosY3" "0.000000"
Option "FSAAMSPosX4" "0.000000"
Option "FSAAMSPosY4" "0.000000"
Option "FSAAMSPosX5" "0.000000"
Option "FSAAMSPosY5" "0.000000"
# === Misc Options ===
Option "UseFastTLS" "0"
Option "BlockSignalsOnLock" "on"
Option "UseInternalAGPGART" "yes"
Option "ForceGenericCPU" "no"
Option "KernelModuleParm" "agplock=0" # AGP locked user pages: disabled
BusID "PCI:2:0:0" # vendor=1002, device=514c
Screen 0
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen0"
Device "ATI Graphics Adapter"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"

Subsection "Display"
Depth 24
Modes "800x600"
ViewPort 0 0 # initial origin if mode is smaller than desktop
Virtual 800 600

EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section # is used alone.

Section "ServerLayout"

# The Identifier line must be present
Identifier "Server Layout"

# Each Screen line specifies a Screen section name, and optionally # the relative position of other screens. The four names after # primary screen name are the screens to the top, bottom, left and right # of the primary screen.

Screen "Screen0"

# Each InputDevice line specifies an InputDevice section name and # optionally some options to specify the way the device is to be # used. Those options include "CorePointer", "CoreKeyboard" and # "SendCoreEvents".

InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"

EndSection

### EOF ###
noi@pcdebian:/etc/X11$

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

arghbis

salops de dauphins

bon et maintenant, c quoi les messages d'erreur?

korben31

euh

Code :

Section "Screen"
Identifier "Screen0"
Device "ATI Graphics Adapter"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"
Subsection "Display"
Depth 24
Modes "800x600"
ViewPort 0 0 # initial origin if mode is smaller than desktop
Virtual 800 600
EndSubsection
EndSection

t'es sure ?

Message édité par korben31 le 14-06-2005 à 11:35:57

el cabron

me gusta el perico

c est ce qu il y a , que dois je modifier ?

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

Nelyot Tchagui

on va faire un test:

mv /etc/X11/XF86Config-4 /etc/X11/XF86Oldconfig

et après tu rempaces tout le contenu de /etc/X11/XF86Config-4 par

# the rights to use, copy, modify, merge, publish, distribute, sublicense, # and/or sell copies of the Software, and to permit persons to whom the # Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in # all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR # IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, # FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL # THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, # WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF # OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE # SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall # not be used in advertising or otherwise to promote the sale, use or other # dealings in this Software without prior written authorization from the # XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of # this file.
# **********************************************************************

# **********************************************************************
# DRI Section
# **********************************************************************
Section "dri"
# Access to OpenGL ICD is allowed for all users:
Mode 0666
# Access to OpenGL ICD is restricted to a specific user group:
# Group 100 # users
# Mode 0660
EndSection

# **********************************************************************
# Module section -- this section is used to specify # which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
# Option "omit xfree86-dga"
EndSubSection

# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"

# This loads the GLX module
Load "glx" # libglx.a
Load "dri" # libdri.a

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set # **********************************************************************

Section "Files"

# The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db" ). There is normally # no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together), # as well as specifying multiple comma-separated entries in one FontPath # command (or a combination of both methods) # # If you don't have a floating point coprocessor and emacs, Mosaic or other # programs take long to start up, try moving the Type1 and Speedo directory # to the end of this list (or comment them out).
#

# FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"

# The module search path. The default path is shown here.

# ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging

# Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence # This allows clients to receive this key event.

# Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching # sequences. This allows clients to receive these key events.

# Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error.

# Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

# Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings.

# Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset).

# Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard" ).
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris), # uncomment the following line.

# Option "Protocol" "Xqueue"

Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"

# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and # control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""

# Option "XkbDisable"

Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "fr"

EndSection

# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "ExplorerPS/2"
Option "Device" "/dev/mouse"

# When using XQUEUE, comment out the above two lines, and uncomment # the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms)

Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection

# **********************************************************************
# Other input device sections
# this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"
Identifier "Monitor0"
HorizSync 31.5 - 108.5
VertRefresh 100 - 100
Option "DPMS"

# === Active Stereo mode lines based on GTF === # XVGA @ 100Hz Modeline "1024x768@100" 113.309 1024 1096 1208 1392 768 769 772 814 +hsync +vsync # XVGA @ 120Hz Modeline "1024x768@120" 139.054 1024 1104 1216 1408 768 769 772 823 +hsync +vsync # SXGA @ 100Hz Modeline "1280x1024@100" 190.960 1280 1376 1520 1760 1024 1025 1028 1085 +hsync +vsync # SXGA @ 120Hz Modeline "1280x1024@120" 233.793 1280 1384 1528 1776 1024 1025 1028 1097 +hsync +vsync

EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"

# The chipset line is optional in most cases. It can be used to override # the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver # modules, this line instructs the server to load the specified driver # module. Even when not using loadable driver modules, this line # indicates which driver should interpret the information in this section.

Driver "vga"
# The BusID line is used to specify which of possibly multiple devices # this section is intended for. When this line isn't present, a device # section can only match up with the primary video device. For PCI # devices a line like the following could be used. This line should not # normally be included unless there is more than one video device # installed.

# BusID "PCI:0:10:0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# === ATI device section ===

Section "Device"
Identifier "ATI Graphics Adapter"
Driver "vesa"
Screen 0
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen0"
Device "ATI Graphics Adapter"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"

Subsection "Display"
Depth 24
Modes "1280x800" "800x600"
ViewPort 0 0 # initial origin if mode is smaller than desktop
Virtual 1280 800

EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section # is used alone.

Section "ServerLayout"

# The Identifier line must be present
Identifier "Server Layout"

# Each Screen line specifies a Screen section name, and optionally # the relative position of other screens. The four names after # primary screen name are the screens to the top, bottom, left and right # of the primary screen.

Screen "Screen0"

# Each InputDevice line specifies an InputDevice section name and # optionally some options to specify the way the device is to be # used. Those options include "CorePointer", "CoreKeyboard" and # "SendCoreEvents".

InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"

EndSection

### EOF ###

ensuite tu nous donnes le résultat des logs d'erreurs s'il y en a

el cabron

me gusta el perico

il n a pas vraiment aimé, meme probleme "impossible demarrer x server"
voici le log:

XFree86 Version 4.3.0.1 (Debian 4.3.0.dfsg.1-14 20050601051219 fabbione@fabbione.net) Release Date: 15 August 2003 X Protocol Version 11, Revision 0, Release 6.6 Build Operating System: Linux 2.4.29-pre2 i686 [ELF] Build Date: 01 June 2005

This version of XFree86 has been extensively modified by the Debian Project, and is not supported by the XFree86 Project, Inc., in any way. Bugs should be reported to the Debian Bug Tracking System; see
<URL: http://www.debian.org/Bugs/Reporting >.

We strongly encourage the use of the "reportbug" package and command to ensure that bug reports contain as much useful information as possible.

Before filing a bug report, you may want to consult the Debian X FAQ:
XHTML version: file:///usr/share/doc/xfree86-common/FAQ.xhtml
plain text version: file:///usr/share/doc/xfree86-common/FAQ.gz

Module Loader present
OS Kernel: Linux version 2.4.27-2-386 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Mon May 16 16:47:51 JST 2005
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Tue Jun 14 14:23:39 2005
(==) Using config file: "/etc/X11/XF86Config-4"
(==) ServerLayout "Default Layout"
(**) |-->Screen "Default Screen" (0)
(**) | |-->Monitor "PTS:a506"
(**) | |-->Device "Carte vidéo générique"
(**) |-->Input Device "Generic Keyboard"
(**) Option "XkbRules" "xfree86"
(**) XKB: rules: "xfree86"
(**) Option "XkbModel" "pc105"
(**) XKB: model: "pc105"
(**) Option "XkbLayout" "fr"
(**) XKB: layout: "fr"
(==) Keyboard: CustomKeycode disabled
(**) |-->Input Device "Configured Mouse"
(WW) The directory "/usr/lib/X11/fonts/cyrillic" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/lib/X11/fonts/CID" does not exist.
Entry deleted from font path.
(**) FontPath set to
"unix/:7100,/usr/lib/X11/fonts/misc,/usr/lib/X11/fonts/100dpi/:unscaled,/usr/lib/X11/fonts/75dpi/:unscaled,/usr/lib/X11/fonts/Type1,/usr/lib/X11/fonts/Speedo,/usr/lib/X11/fonts/100dpi,/usr/lib/X11/fonts/75dpi"
(==) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(++) using VT number 7

(II) Open APM successful
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.2
XFree86 Video Driver: 0.6
XFree86 XInput driver : 0.4
XFree86 Server Extension : 0.2
XFree86 Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x8000002c, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 10de,01e0 card 1043,80ac rev c1 class 06,00,00 hdr 80
(II) PCI: 00:00:1: chip 10de,01ea card 1043,80ac rev c1 class 05,00,00 hdr 80
(II) PCI: 00:00:2: chip 10de,01ee card 1043,80ac rev c1 class 05,00,00 hdr 80
(II) PCI: 00:00:3: chip 10de,01ed card 1043,80ac rev c1 class 05,00,00 hdr 80
(II) PCI: 00:00:4: chip 10de,01ec card 1043,80ac rev c1 class 05,00,00 hdr 80
(II) PCI: 00:00:5: chip 10de,01ef card 1043,80ac rev c1 class 05,00,00 hdr 80
(II) PCI: 00:01:0: chip 10de,0060 card 1043,80ad rev a4 class 06,01,00 hdr 80
(II) PCI: 00:01:1: chip 10de,0064 card 1043,0c11 rev a2 class 0c,05,00 hdr 80
(II) PCI: 00:02:0: chip 10de,0067 card 1043,0c11 rev a4 class 0c,03,10 hdr 80
(II) PCI: 00:02:1: chip 10de,0067 card 1043,0c11 rev a4 class 0c,03,10 hdr 80
(II) PCI: 00:02:2: chip 10de,0068 card 1043,0c11 rev a4 class 0c,03,20 hdr 80
(II) PCI: 00:04:0: chip 10de,0066 card 1043,80a7 rev a1 class 02,00,00 hdr 00
(II) PCI: 00:06:0: chip 10de,006a card 1043,8095 rev a1 class 04,01,00 hdr 00
(II) PCI: 00:08:0: chip 10de,006c card 0000,0000 rev a3 class 06,04,00 hdr 01
(II) PCI: 00:09:0: chip 10de,0065 card 1043,0c11 rev a2 class 01,01,8a hdr 00
(II) PCI: 00:1e:0: chip 10de,01e8 card 0000,0000 rev c1 class 06,04,00 hdr 01
(II) PCI: 02:00:0: chip 1002,514c card 1002,013a rev 00 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,2), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:1:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:8:0), (0,1,1), BCTRL: 0x0202 (VGA_EN is cleared)
(II) PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:30:0), (0,2,2), BCTRL: 0x000a (VGA_EN is set)
(II) Bus 2 I/O range:
[0] -1 0 0x0000c000 - 0x0000cfff (0x1000) IX[B]
(II) Bus 2 non-prefetchable memory range:
[0] -1 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B]
(II) Bus 2 prefetchable memory range:
[0] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B]
(--) PCI:*(2:0:0) ATI Technologies Inc Radeon R200 QL [Radeon 8500 LE] rev 0, Mem @ 0xd8000000/27, 0xe1000000/16, I/O @ 0xc000/8
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xd0000000 from 0xd7ffffff to 0xcfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xe2002000 - 0xe2002fff (0x1000) MX[B]
[1] -1 0 0xe2001000 - 0xe2001fff (0x1000) MX[B]
[2] -1 0 0xe2000000 - 0xe20000ff (0x100) MX[B]
[3] -1 0 0xe2005000 - 0xe2005fff (0x1000) MX[B]
[4] -1 0 0xe2004000 - 0xe2004fff (0x1000) MX[B]
[5] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[6] -1 0 0xe1000000 - 0xe100ffff (0x10000) MX[B](B)
[7] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[8] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[9] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[10] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[11] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[12] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[13] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xe2002000 - 0xe2002fff (0x1000) MX[B]
[1] -1 0 0xe2001000 - 0xe2001fff (0x1000) MX[B]
[2] -1 0 0xe2000000 - 0xe20000ff (0x100) MX[B]
[3] -1 0 0xe2005000 - 0xe2005fff (0x1000) MX[B]
[4] -1 0 0xe2004000 - 0xe2004fff (0x1000) MX[B]
[5] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[6] -1 0 0xe1000000 - 0xe100ffff (0x10000) MX[B](B)
[7] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[8] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[9] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[10] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[11] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[12] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[13] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe2002000 - 0xe2002fff (0x1000) MX[B]
[6] -1 0 0xe2001000 - 0xe2001fff (0x1000) MX[B]
[7] -1 0 0xe2000000 - 0xe20000ff (0x100) MX[B]
[8] -1 0 0xe2005000 - 0xe2005fff (0x1000) MX[B]
[9] -1 0 0xe2004000 - 0xe2004fff (0x1000) MX[B]
[10] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[11] -1 0 0xe1000000 - 0xe100ffff (0x10000) MX[B](B)
[12] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[15] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[16] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[17] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[18] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[19] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[20] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B](B)
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_clip.o": No symbols found Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_norm.o": No symbols found Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_xform.o": No symbols found Skipping "/usr/X11R6/lib/modules/extensions/libGLcore.a:m_debug_vertex.o": No symbols found
(II) Module GLcore: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.2
(II) LoadModule: "bitmap"
(II) Reloading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Loading font Bitmap
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) LoadModule: "dri"
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
(II) Module dri: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.2
(II) Loading sub module "drm"
(II) LoadModule: "drm"
(II) Loading /usr/X11R6/lib/modules/linux/libdrm.a
(II) Module drm: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.2
(II) Loading extension XFree86-DRI
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a
(II) Module freetype: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 2.0.2
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.2
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Reloading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Loading extension GLX
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) LoadModule: "record"
(II) Loading /usr/X11R6/lib/modules/extensions/librecord.a
(II) Module record: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.13.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.2
(II) Loading extension RECORD
(II) LoadModule: "speedo"
(II) Loading /usr/X11R6/lib/modules/fonts/libspeedo.a
Skipping "/usr/X11R6/lib/modules/fonts/libspeedo.a:spencode.o": No symbols found
(II) Module speedo: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.1
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.4
(II) Loading font Speedo
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.2
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) LoadModule: "ati"
(II) Loading /usr/X11R6/lib/modules/drivers/ati_drv.o
(II) Module ati: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 6.5.5
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.6
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.4
(II) ATI: ATI driver (version 6.5.5) for chipsets: ati, ativga
(II) R128: Driver for ATI Rage 128 chipsets:
ATI Rage 128 Mobility M3 LE (PCI), ATI Rage 128 Mobility M3 LF (AGP),
ATI Rage 128 Mobility M4 MF (AGP), ATI Rage 128 Mobility M4 ML (AGP),
ATI Rage 128 Pro GL PA (AGP?), ATI Rage 128 Pro GL PB (AGP?),
ATI Rage 128 Pro GL PC (AGP?), ATI Rage 128 Pro GL PD (PCI),
ATI Rage 128 Pro GL PE (AGP?), ATI Rage 128 Pro GL PF (AGP),
ATI Rage 128 Pro VR PG (AGP?), ATI Rage 128 Pro VR PH (AGP?),
ATI Rage 128 Pro VR PI (AGP?), ATI Rage 128 Pro VR PJ (AGP?),
ATI Rage 128 Pro VR PK (AGP?), ATI Rage 128 Pro VR PL (AGP?),
ATI Rage 128 Pro VR PM (AGP?), ATI Rage 128 Pro VR PN (AGP?),
ATI Rage 128 Pro VR PO (AGP?), ATI Rage 128 Pro VR PP (PCI),
ATI Rage 128 Pro VR PQ (AGP?), ATI Rage 128 Pro VR PR (PCI),
ATI Rage 128 Pro VR PS (AGP?), ATI Rage 128 Pro VR PT (AGP?),
ATI Rage 128 Pro VR PU (AGP?), ATI Rage 128 Pro VR PV (AGP?),
ATI Rage 128 Pro VR PW (AGP?), ATI Rage 128 Pro VR PX (AGP?),
ATI Rage 128 GL RE (PCI), ATI Rage 128 GL RF (AGP),
ATI Rage 128 RG (AGP), ATI Rage 128 VR RK (PCI),
ATI Rage 128 VR RL (AGP), ATI Rage 128 4X SE (AGP?),
ATI Rage 128 4X SF (AGP?), ATI Rage 128 4X SG (AGP?),
ATI Rage 128 4X SH (AGP?), ATI Rage 128 4X SK (AGP?),
ATI Rage 128 4X SL (AGP?), ATI Rage 128 4X SM (AGP),
ATI Rage 128 4X SN (AGP?), ATI Rage 128 Pro ULTRA TF (AGP),
ATI Rage 128 Pro ULTRA TL (AGP), ATI Rage 128 Pro ULTRA TR (AGP),
ATI Rage 128 Pro ULTRA TS (AGP?), ATI Rage 128 Pro ULTRA TT (AGP?),
ATI Rage 128 Pro ULTRA TU (AGP?)
(II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI Radeon VE/7000 QY (AGP/PCI), ATI Radeon VE/7000 QZ (AGP/PCI),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI Radeon IGP320 (A3) 4136, ATI Radeon IGP320M (U1) 4336,
ATI Radeon IGP330/340/350 (A4) 4137,
ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI Radeon 7000 IGP (A4+) 4237, ATI Radeon Mobility 7000 IGP 4437,
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
ATI Radeon 9100 QM (AGP), ATI Radeon 8500 AIW BB (AGP),
ATI Radeon 8500 AIW BC (AGP), ATI Radeon 7500 QW (AGP/PCI),
ATI Radeon 7500 QX (AGP/PCI), ATI Radeon 9000/PRO If (AGP/PCI),
ATI Radeon 9000 Ig (AGP/PCI), ATI FireGL Mobility 9000 (M9) Ld (AGP),
ATI Radeon Mobility 9000 (M9) Lf (AGP),
ATI Radeon Mobility 9000 (M9) Lg (AGP),
ATI Radeon 9100 IGP (A5) 5834,
ATI Radeon Mobility 9100 IGP (U3) 5835,
ATI Radeon 9200PRO 5960 (AGP), ATI Radeon 9200 5961 (AGP),
ATI Radeon 9200 5962 (AGP), ATI Radeon 9200SE 5964 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
ATI Radeon Mobility 9200 (M9+) 5C63 (AGP), ATI Radeon 9500 AD (AGP),
ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
ATI FireGL Z1 AG (AGP), ATI Radeon 9700 Pro ND (AGP),
ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9700 NF (AGP),
ATI FireGL X1 NG (AGP), ATI Radeon 9600 AP (AGP),
ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP),
ATI FireGL RV360 AV (AGP), ATI Radeon Mobility 9600 (M10) NP (AGP),
ATI Radeon Mobility 9600 (M10) NQ (AGP),
ATI Radeon Mobility 9600 (M11) NR (AGP),
ATI Radeon Mobility 9600 (M10) NS (AGP),
ATI FireGL Mobility T2 (M10) NT (AGP),
ATI FireGL Mobility T2 (M11) NV (AGP), ATI Radeon 9800SE AH (AGP),
ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
ATI FireGL X2 AK (AGP), ATI Radeon 9800PRO NH (AGP),
ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
ATI Radeon 9800XT NJ (AGP)
(II) Primary Device is: PCI 02:00:0
(II) ATI: Candidate "Device" section "Carte vidéo générique".
(--) Assigning device section with no busID to primary device
(--) Chipset ATI Radeon 8500 QL (AGP) found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe2002000 - 0xe2002fff (0x1000) MX[B]
[6] -1 0 0xe2001000 - 0xe2001fff (0x1000) MX[B]
[7] -1 0 0xe2000000 - 0xe20000ff (0x100) MX[B]
[8] -1 0 0xe2005000 - 0xe2005fff (0x1000) MX[B]
[9] -1 0 0xe2004000 - 0xe2004fff (0x1000) MX[B]
[10] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[11] -1 0 0xe1000000 - 0xe100ffff (0x10000) MX[B](B)
[12] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[15] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[16] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[17] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[18] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[19] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[20] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B](B)
(II) Loading sub module "radeon"
(II) LoadModule: "radeon"
(II) Loading /usr/X11R6/lib/modules/drivers/radeon_drv.o
(II) Module radeon: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 4.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.6
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe2002000 - 0xe2002fff (0x1000) MX[B]
[6] -1 0 0xe2001000 - 0xe2001fff (0x1000) MX[B]
[7] -1 0 0xe2000000 - 0xe20000ff (0x100) MX[B]
[8] -1 0 0xe2005000 - 0xe2005fff (0x1000) MX[B]
[9] -1 0 0xe2004000 - 0xe2004fff (0x1000) MX[B]
[10] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[11] -1 0 0xe1000000 - 0xe100ffff (0x10000) MX[B](B)
[12] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[13] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[14] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[15] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[18] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[19] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[20] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[21] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[22] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[23] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B](B)
[24] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[25] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) RADEON(0): MMIO registers at 0xe1000000
(WW) System lacks support for changing MTRRs
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) RADEON(0): PCI bus 2 card 0 func 0
(**) RADEON(0): Depth 24, (--) framebuffer bpp 32
(II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) RADEON(0): Default visual is TrueColor
(==) RADEON(0): RGB weight 888
(II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/X11R6/lib/modules/linux/libint10.a
(II) RADEON(0): initializing int10
(WW) RADEON(0): Bad V_BIOS checksum
(II) RADEON(0): Primary V_BIOS segment is: 0xc000
(--) RADEON(0): Chipset: "ATI Radeon 8500 QL (AGP)" (ChipID = 0x514c)
(--) RADEON(0): Linear framebuffer at 0xd8000000
(--) RADEON(0): VideoRAM: 65536 kByte (128 bit DDR SDRAM)
(II) RADEON(0): AGP card detected
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.a
(II) Module i2c: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.2.0
ABI class: XFree86 Video Driver, version 0.6
(II) RADEON(0): I2C bus "DDC" initialized.
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): DDC Type: 2, Detected Type: 0
(II) RADEON(0): DDC Type: 4, Detected Type: 0
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): DDC Type: 3, Detected Type: 1
(II) RADEON(0): Displays Detected: Monitor1--Type 1, Monitor2--Type 0

(II) RADEON(0): Monitor1 EDID data ---------------------------
(II) RADEON(0): Manufacturer: PTS Model: 6a5 Serial#: 83239
(II) RADEON(0): Year: 2005 Week: 3
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
(II) RADEON(0): Sync: Separate
(II) RADEON(0): Max H-Image Size [cm]: horiz.: 34 vert.: 27
(II) RADEON(0): Gamma: 2.50
(II) RADEON(0): DPMS capabilities: Off; RGB/Color Display
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.630 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) RADEON(0): blueX: 0.148 blueY: 0.098 whiteX: 0.310 whiteY: 0.330
(II) RADEON(0): Supported VESA Video Modes:
(II) RADEON(0): 720x400@70Hz
(II) RADEON(0): 640x480@60Hz
(II) RADEON(0): 640x480@67Hz
(II) RADEON(0): 640x480@72Hz
(II) RADEON(0): 640x480@75Hz
(II) RADEON(0): 800x600@56Hz
(II) RADEON(0): 800x600@60Hz
(II) RADEON(0): 800x600@72Hz
(II) RADEON(0): 800x600@75Hz
(II) RADEON(0): 832x624@75Hz
(II) RADEON(0): 1024x768@60Hz
(II) RADEON(0): 1024x768@70Hz
(II) RADEON(0): 1024x768@75Hz
(II) RADEON(0): 1280x1024@75Hz
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported Future Video Modes:
(II) RADEON(0): #4: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) RADEON(0): Supported additional Video Mode:
(II) RADEON(0): clock: 108.0 MHz Image Size: 337 x 270 mm
(II) RADEON(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) RADEON(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) RADEON(0): Supported additional Video Mode:
(II) RADEON(0): clock: 78.8 MHz Image Size: 337 x 270 mm
(II) RADEON(0): h_active: 1024 h_sync: 1040 h_sync_end 1136 h_blank_end 1312 h_border: 0
(II) RADEON(0): v_active: 768 v_sync: 769 v_sync_end 772 v_blanking: 800 v_border: 0
(II) RADEON(0): Ranges: V min: 60 V max: 75 Hz, H min: 30 H max: 80 kHz, PixClock max 140 MHz
(II) RADEON(0): Serial No: F5UQ510183239
(II) RADEON(0): End of Monitor1 EDID data --------------------
(II) RADEON(0):
(II) RADEON(0): Primary Display == Type 1
(==) RADEON(0): Using gamma correction (1.0, 1.0, 1.0)
(II) RADEON(0): Validating modes on Primary head ---------
(II) RADEON(0): PTS:a506: Using hsync range of 30.00-80.00 kHz
(II) RADEON(0): PTS:a506: Using vrefresh range of 60.00-75.00 Hz
(II) RADEON(0): Clock range: 20.00 to 350.00 MHz
(II) RADEON(0): Not using default mode "640x350" (vrefresh out of range)
(II) RADEON(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "640x400" (vrefresh out of range)
(II) RADEON(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "720x400" (vrefresh out of range)
(II) RADEON(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "640x480" (vrefresh out of range)
(II) RADEON(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "800x600" (vrefresh out of range)
(II) RADEON(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "800x600" (vrefresh out of range)
(II) RADEON(0): Not using default mode "400x300" (vrefresh out of range)
(II) RADEON(0): Not using default mode "1024x768" (vrefresh out of range)
(II) RADEON(0): Not using default mode "512x384" (vrefresh out of range)
(II) RADEON(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1024x768" (vrefresh out of range)
(II) RADEON(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1280x960" (hsync out of range)
(II) RADEON(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1280x1024" (hsync out of range)
(II) RADEON(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,PTS:a506) mode clock 162MHz exceeds DDC maximum 140MHz
(II) RADEON(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1600x1200" (hsync out of range)
(II) RADEON(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1600x1200" (hsync out of range)
(II) RADEON(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1600x1200" (hsync out of range)
(II) RADEON(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1600x1200" (hsync out of range)
(II) RADEON(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1792x1344" (hsync out of range)
(II) RADEON(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1792x1344" (hsync out of range)
(II) RADEON(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1856x1392" (hsync out of range)
(II) RADEON(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1856x1392" (hsync out of range)
(II) RADEON(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1920x1440" (hsync out of range)
(II) RADEON(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1920x1440" (hsync out of range)
(II) RADEON(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1152x768" (vrefresh out of range)
(II) RADEON(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1400x1050" (hsync out of range)
(II) RADEON(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1920x1440" (hsync out of range)
(II) RADEON(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "2048x1536" (hsync out of range)
(II) RADEON(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "2048x1536" (hsync out of range)
(II) RADEON(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) RADEON(0): Not using default mode "1600x1200" (width too large for virtual size)
(II) RADEON(0): Not using default mode "1400x1050" (width too large for virtual size)
(II) RADEON(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) RADEON(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) RADEON(0): Not using default mode "1280x960" (width too large for virtual size)
(II) RADEON(0): Not using default mode "1152x864" (width too large for virtual size)
(II) RADEON(0): Not using default mode "1024x768" (width too large for virtual size)
(II) RADEON(0): Not using default mode "1024x768" (width too large for virtual size)
(II) RADEON(0): Not using default mode "1024x768" (width too large for virtual size)
(II) RADEON(0): Not using default mode "832x624" (width too large for virtual size)
(--) RADEON(0): Virtual size is 800x600 (pitch 832)
(**) RADEON(0): *Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz
(II) RADEON(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync
(**) RADEON(0): *Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz
(II) RADEON(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
(**) RADEON(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz
(II) RADEON(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
(**) RADEON(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) RADEON(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
(**) RADEON(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz
(II) RADEON(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync
(**) RADEON(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz
(II) RADEON(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync
(**) RADEON(0): Default mode "416x312": 28.6 MHz, 49.7 kHz, 74.7 Hz (D)
(II) RADEON(0): Modeline "416x312" 28.64 416 432 464 576 312 312 314 333 doublescan -hsync
-vsync
(**) RADEON(0): Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D)
(II) RADEON(0): Modeline "400x300" 24.75 400 408 448 528 300 300 302 312 doublescan +hsync
+vsync
(**) RADEON(0): Default mode "400x300": 25.0 MHz, 48.1 kHz, 72.2 Hz (D)
(II) RADEON(0): Modeline "400x300" 25.00 400 428 488 520 300 318 321 333 doublescan +hsync
+vsync
(**) RADEON(0): Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D)
(II) RADEON(0): Modeline "400x300" 20.00 400 420 484 528 300 300 302 314 doublescan +hsync
+vsync
(--) RADEON(0): Display dimensions: (340, 270) mm
(--) RADEON(0): DPI set to (59, 56)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.2
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) RADEON(0): AGP Fast Write disabled by default
(II) RADEON(0): Depth moves disabled by default
(II) Loading sub module "shadowfb"
(II) LoadModule: "shadowfb"
(II) Loading /usr/X11R6/lib/modules/libshadowfb.a
(II) Module shadowfb: vendor="The XFree86 Project"
compiled for 4.3.0.1, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.2
(II) RADEON(0): Page flipping disabled
(!!) RADEON(0): For information on using the multimedia capabilities
of this adapter, please see http://gatos.sf.net.
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xe1000000 - 0xe100ffff (0x10000) MX[B]
[1] 0 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B]
[2] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[7] -1 0 0xe2002000 - 0xe2002fff (0x1000) MX[B]
[8] -1 0 0xe2001000 - 0xe2001fff (0x1000) MX[B]
[9] -1 0 0xe2000000 - 0xe20000ff (0x100) MX[B]
[10] -1 0 0xe2005000 - 0xe2005fff (0x1000) MX[B]
[11] -1 0 0xe2004000 - 0xe2004fff (0x1000) MX[B]
[12] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[13] -1 0 0xe1000000 - 0xe100ffff (0x10000) MX[B](B)
[14] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B](B)
[15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprU)
[16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprU)
[17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprU)
[18] 0 0 0x0000c000 - 0x0000c0ff (0x100) IX[B]
[19] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[20] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[21] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[22] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[23] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[24] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[25] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[26] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B](B)
[27] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[28] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) RADEON(0): Wrote: rd=12, fd=132, pd=6
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 5, (OK)
drmGetBusid returned ''
(II) RADEON(0): [drm] loaded kernel module for "radeon" driver
(II) RADEON(0): [drm] created "radeon" driver at busid "PCI:2:0:0"
(II) RADEON(0): [drm] added 8192 byte SAREA at 0xe09bd000
(II) RADEON(0): [drm] mapped SAREA 0xe09bd000 to 0x40018000
(II) RADEON(0): [drm] framebuffer handle = 0xd8000000
(II) RADEON(0): [drm] added 1 reserved context for kernel
(II) RADEON(0): [agp] Mode 0x1f000201 [AGP 0x10de/0x01e0; Card 0x1002/0x514c]
(II) RADEON(0): [agp] 8192 kB allocated with handle 0xe49c1000
(II) RADEON(0): [agp] ring handle = 0xd0000000
(II) RADEON(0): [agp] Ring mapped at 0x4426b000
(II) RADEON(0): [agp] ring read ptr handle = 0xd0101000
(II) RADEON(0): [agp] Ring read ptr mapped at 0x4001a000
(II) RADEON(0): [agp] vertex/indirect buffers handle = 0xd0102000
(II) RADEON(0): [agp] Vertex/indirect buffers mapped at 0x4436c000
(II) RADEON(0): [agp] GART texture map handle = 0xd0302000
(II) RADEON(0): [agp] GART Texture map mapped at 0x4456c000
(II) RADEON(0): [drm] register handle = 0xe1000000
(II) RADEON(0): [dri] Visual configs initialized
(II) RADEON(0): CP in BM mode
(II) RADEON(0): Using 8 MB GART aperture
(II) RADEON(0): Using 1 MB for the ring buffer
(II) RADEON(0): Using 2 MB for vertex/indirect buffers
(II) RADEON(0): Using 5 MB for GART textures
(II) RADEON(0): Memory manager initialized to (0,0) (832,8191)
(II) RADEON(0): Reserved area from (0,600) to (832,602)
(II) RADEON(0): Largest offscreen area available: 832 x 7589
(II) RADEON(0): Will use back buffer at offset 0x82a000
(II) RADEON(0): Will use depth buffer at offset 0xa12000
(II) RADEON(0): Will use 53248 kb for textures at offset 0xc00000
(II) RADEON(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Lines
Scanline Image Writes
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128 slots
28 256x256 slots
13 512x512 slots
(II) RADEON(0): Acceleration enabled
(==) RADEON(0): Backing store disabled
(==) RADEON(0): Silken mouse enabled
(II) RADEON(0): Using hardware cursor (scanline 602)
(II) RADEON(0): Largest offscreen area available: 832 x 7584
(**) Option "dpms"
(**) RADEON(0): DPMS enabled
(II) RADEON(0): X context handle = 0x00000001
(II) RADEON(0): [drm] installed DRM signal handler
(II) RADEON(0): [DRI] installation complete
(II) RADEON(0): [drm] Added 32 65536 byte vertex/indirect buffers
(II) RADEON(0): [drm] Mapped 32 vertex/indirect buffers
(II) RADEON(0): [drm] dma control initialized, using IRQ 12
(II) RADEON(0): [drm] Initialized kernel GART heap manager, 5111808
(II) RADEON(0): Direct rendering enabled
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Keyboard "Generic Keyboard" handled by legacy driver
(**) Option "Protocol" "ImPS/2"
(**) Configured Mouse: Protocol: "ImPS/2"
(**) Option "CorePointer"
(**) Configured Mouse: Core Pointer
(**) Option "Device" "/dev/input/mice"
(**) Option "Emulate3Buttons" "true"
(**) Configured Mouse: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5"
(**) Configured Mouse: ZAxisMapping: buttons 4 and 5
(**) Configured Mouse: Buttons: 5
(II) XINPUT: Adding extended input device "Configured Mouse" (type: MOUSE)
(II) Configured Mouse: ps2EnableDataReporting: succeeded
Warning: font renderer for ".pcf" already registered at priority 0
Warning: font renderer for ".pcf.Z" already registered at priority 0
Warning: font renderer for ".pcf.gz" already registered at priority 0
Warning: font renderer for ".snf" already registered at priority 0
Warning: font renderer for ".snf.Z" already registered at priority 0
Warning: font renderer for ".snf.gz" already registered at priority 0
Warning: font renderer for ".bdf" already registered at priority 0
Warning: font renderer for ".bdf.Z" already registered at priority 0
Warning: font renderer for ".bdf.gz" already registered at priority 0
Warning: font renderer for ".pmf" already registered at priority 0 Could not init font path element unix/:7100, removing from list!
SetClientVersion: 0 9

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

korben31

euh
colle nous ski dit au startx plutot

el cabron

me gusta el perico

j ai simplement un message du genre "impossible demarrer Xserver" et ensuite dans le detail de l erreur j ai ce que j ai exactement ce qu il y a dans le log

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

Nelyot Tchagui

vu qu'il y a plusieurs problèmes liés à ton ATI et l'accéleration 3D, mets toi en console total, supprime le fichier /etc/X11/XF86Config-4,
et lance dpkg-reconfigure xfree86-xserver en cochant toutes les résolutions qui t'intéresse et en choisissant un driver standard pour ta CG (pas le proprio d'ATI)

arghbis

salops de dauphins

le driver pour les radeon, il s'appelle radeon...

el cabron

me gusta el perico

j ai supprimé XF86Config-4, lancé dpkg-reconfigure xserver-xfree86, choisis VGA pour le pilote, mais j ai exactement le meme probleme..
que dois je mettre dans "identifiant du bus de la carte video" ?
et dans " modules du serveur XFree86 qui seront chargé par defaut" ?

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

Nelyot Tchagui

choisi "radeon" comme le suggère arghbis en driver, je suppose que ce doit être le driver libre standard

arghbis

salops de dauphins

y'a un truc que je comprends pas : tu as une radeon 8500. Pourquoi ne choisis-tu pas le pilote radeon lors du dpkg-reconfigure? il est fait pour ça!

pour les modules, tu peux laisser les choix par défaut (mais assures-toi que le dri est chargé et GLcore aussi je crois)

el cabron

me gusta el perico

dans la liste je n ai pas "radeon" (uniquement ATI)

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

arghbis

salops de dauphins

ils ont p'tet changé le nom. met le ATI (c'est le driver libre)

el cabron

me gusta el perico

j ai testé avec ATI ou VGA sans succés
maintenant le detail du message d erreur est bien plus court, j ai un :
fatal server error:
no screens found

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

arghbis

salops de dauphins

bon fais un : cat /var/log/XFree86.0.log | grep EE

et donnes nous le résultat

zanton

écran vga ou dvi ? quelle résolution tu veux précisément ?

el cabron

me gusta el perico

c est un ecran LCD .
a force de bidouillé il m etait impossible de redemarrer, comme l installation n avait que 24H00 j ai reinstallé DEBIAN.et la miracle sans rien faire de special j ai bien la possibilité de choisir plusieurs resolutions.
j ai installé les pilotes ATI et boum,meme chose ..
je pense que je dois merder dans la config de fglrxconfig.
je me passerais donc des pilotes ATI ..

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

Nelyot Tchagui

la réinstallation est rarement la bonne solution, mais dans ton cas, tant mieux si ça marche comme ça

el cabron

me gusta el perico

c est clair, c est frustrant de passer par une reinstallation pour resoudre un probleme.
merci a tous pour votre aide

---------------
Rechercher le bonheur, c'est l'occupation des gens tristes.

Zzozo

Modérateur
Un peu, passionément, à la fol

[:xx_xx]
Ha ouais, "El Cabron" ...
[:janfynette]

---------------
« Ce qui ne vous tue pas vous rend plus fort » F. Nietzsche | « Vise_ la Lune. Si tu rates, au pire, t'es dans la merde » Un poète disparu dans le cercle

Publicité

FORUM HardWare.fr

Linux et OS Alternatifs

Installation

resolution graphique sous sarge

Sujets relatifs
Sarge et et le son.	[debian sarge] migration testing => stable
Sarge est enfin sortie !	Encore un problème d'installation debian sarge.
Pb touche "ctrl, alt, alt gr et shift" sous débian sarge	Debian Sarge et VAIO VGN-FS115Z
(Ubuntu) Probleme résolution de l'ecran	Pb demarrage Xserver sous Debian Sarge
Dual screen avec une seuls carte graphique	problemes debian sarge
Plus de sujets relatifs à : resolution graphique sous sarge

Page générée en 0.143 secondes