Citation :
ctl 0xBE2 bmdma 0xC800 irq 17
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC808 irq 17
ata3: SATA link up 1.5 Gbps (SStatus 113)
ata3: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e9 86:3c02 87:4023 88:203f
ata3: dev 0 ATA-6, max UDMA/100, 321672960 sectors: LBA48
ata3(0): applying bridge limits
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata3: dev 0 configured for UDMA/100
scsi2 : sata_nv
ata4: SATA link up 1.5 Gbps (SStatus 113)
ata4: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4773 85:7c69 86:3e01 87:4763 88:407f
ata4: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata4: dev 0 configured for UDMA/133
scsi3 : sata_nv
Vendor: ATA Model: HDS722516VLAT80 Rev: V34O
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: Maxtor 6V300F0 Rev: VA11
Type: Direct-Access ANSI SCSI revision: 05
st: Version 20050830, fixed bufsize 32768, s/g segs 256
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1
sd 2:0:0:0: Attached scsi disk sda
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: unknown partition table
sd 3:0:0:0: Attached scsi disk sdb
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 3:0:0:0: Attached scsi generic sg1 type 0
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:07.2[B] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[fdeff000-fdeff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 19
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[fdefe000-fdefe7ff] Max Packet=[2048] IR/IT contexts=[4/8]
video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1)
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 21, io mem 0xfe02f000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
Initializing USB Mass Storage driver...
usb 2-1: new full speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 2-4: new low speed USB device using ohci_hcd and address 3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0151125f75]
usb 2-4: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-4
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c40
ieee1394: Host added: ID:BUS[1-00:1023] GUID[0001292000023c3f]
input: AT Translated Set 2 keyboard as /class/input/input1
it87: Found IT8712F chip at 0x290, revision 7
Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC).
ALSA device list:
No soundcards found.
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8183 buckets, 65464 max) - 172 bytes per conntrack
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 164k freed
Adding 1461872k swap on /dev/hda6. Priority:-1 extents:1 across:1461872k
EXT3 FS on hda2, internal journal
drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0
usbcore: registered new driver visor
drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 22
bttv0: Bt878 (rev 17) at 0000:01:06.0, irq: 22, latency: 32, mmio: 0xfdfff000
bttv0: detected: Pinnacle PCTV [bswap] [card=39], PCI subsystem ID is bd11:1200
bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ff27ff [init]
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: miro: id=9 tuner=3 radio=no stereo=no
bttv0: using tuner=3
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner 2-0060: All bytes are equal. It is not a TEA5767
tuner 2-0060: chip found @ 0xc0 (bt878 #0 [sw])
tuner 2-0060: type set to 3 (Philips (SECAM+PAL_BG) (FI1216MF, FM1216MF, FR1216MF))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth2: forcedeth.c: subsystem: 010de:cb84 bound to 0000:00:0a.0
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sdb, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 22
sk98lin: Could not read VPD data.
ACPI: PCI interrupt for device 0000:01:0a.0 disabled
sk98lin: probe of 0000:01:0a.0 failed with error -5
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 23
Installing spdif_bug patch: Audigy 2 ZS [SB0350]
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:05:00.0 to 64
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8774 Tue Aug 1 20:54:08 PDT 2006
i2c_adapter i2c-3: SMBus Quick command not supported, can't probe for chips
i2c_adapter i2c-4: SMBus Quick command not supported, can't probe for chips
i2c_adapter i2c-5: SMBus Quick command not supported, can't probe for chips
hda: cache flushes supported
pwc: Philips webcam module version 10.0.12-rc1-debian loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
pwc: Trace options: 0x0001
pwc: Logitech QuickCam 4000 Pro USB webcam detected.
pwc: Registered as /dev/video1.
usbcore: registered new driver Philips webcam
|
FORUM HardWare.fr
