Voila je viens de suiivre tte la procédure pour dezonner ce lecteur et rien n'y
mon firware rcp 2 est f303 , g telecharger le firware rpc1 e303com.bin , g telecharger mtkfash 1.24 et suivit la procédure
seulement voila que d e tappe upgrade.bat , un message d'erreur aparait me disant:
"error!no firware found.PLease download and copy it to the same dir "
alors que mon fichier .bin se trouve bien ds le rep indiqué
g meme essayer en copiant tt sur la diskette mais ts pareil
alors pour voir la couille ki avais ,e suis alé sois sous windos (xp pro sp1) et a l'invite de commade g tapé:
d:\mtk124\type upgrade.bat
et voila ce qu'il me met :
Citation :
D:\mtk124>type upgrade.bat
@echo off
cls
if not exist version.inf goto nopatch
type version.inf
echo.
echo Use in MS-DOS MODE or COMMAND PROMPT MODE only!
echo WARNING: USE AT YOUR OWN RISK!
echo.
echo Most drives can only flashed as SECONDARY SLAVE!
echo If the flasher hang please try first to reconnect
echo and configure the drive.
echo Ignore the reboot messages of MKTFLASH!!!
echo.
echo -------------------------------
echo How's your DVD drive connected?
echo 1. MASTER on PRIMARY IDE port
echo 2. SLAVE on PRIMARY IDE port
echo 3. MASTER on SECONDARY IDE port
echo 4. SLAVE on SECONDARY IDE port
echo 0. Abort ----------------------
:keyloop
key
if errorlevel 53 goto keyloop
if errorlevel 52 goto choice4
if errorlevel 51 goto choice3
if errorlevel 50 goto choice2
if errorlevel 49 goto choice1
if errorlevel 48 goto end
goto keyloop
:choice1
echo.
echo DVD drive is connected as MASTER on PRIMARY IDE port.
echo Are you sure you want to upgrade the firmware?
echo.
pause
echo Backing up drive's firmware ...
mtkflash 1 r /a0 /b back00.bin
mtkflash 1 r /a1 /b back01.bin
echo Press CTRL+C to break if you get an Unknown Flash message
pause
echo Now flashing the drive ...
mtkflash 1 w /a0 /b bide00.bin
mtkflash 1 w /a1 /b bide01.bin
echo OK!
goto end
:choice2
echo.
echo DVD drive is connected as SLAVE on PRIMARY IDE port.
echo Are you sure you want to upgrade the firmware?
echo.
pause
echo Backing up drive's firmware ...
mtkflash 2 r /a0 /b back00.bin
mtkflash 2 r /a1 /b back01.bin
echo Press CTRL+C to break if you get an Unknown Flash message
pause
echo Now flashing the drive ...
mtkflash 2 w /a0 /b bide00.bin
mtkflash 2 w /a1 /b bide01.bin
echo OK!
goto end
:choice3
echo.
echo DVD drive is connected as MASTER on SECONDARY IDE port.
echo Are you sure you want to upgrade the firmware?
echo.
pause
echo Backing up drive's firmware ...
mtkflash 3 r /a0 /b back00.bin
mtkflash 3 r /a1 /b back01.bin
echo Press CTRL+C to break if you get an Unknown Flash message
pause
echo Now flashing the drive ...
mtkflash 3 w /a0 /b bide00.bin
mtkflash 3 w /a1 /b bide01.bin
echo OK!
goto end
:choice4
echo.
echo DVD drive is connected as SLAVE on SECONDARY IDE port.
echo Are you sure you want to upgrade the firmware?
echo.
pause
echo Backing up drive's firmware ...
mtkflash 4 r /a0 /b back00.bin
mtkflash 4 r /a1 /b back01.bin
echo Press CTRL+C to break if you get an Unknown Flash message
pause
echo Now flashing the drive ...
mtkflash 4 w /a0 /b bide00.bin
mtkflash 4 w /a1 /b bide01.bin
echo OK!
goto end
:nopatch
echo.
echo ERROR! No Fimware found. Please download and copy it to the same dir.
echo.
pause
:end
D:\mtk124>
|
donc si on regarde la line 3 y dis:
Citation :
[quote]if not exist version.inf goto nopatch
|
et evidement je n'est pas le fichier .inf
donc je vais a nopatch et on trouve:
Citation :
[quote]:nopatch
echo.
echo ERROR! No Fimware found. Please download and copy it to the same dir.
echo.
pause
:end
|
donc cela explique le message d'erreur mais sur la procedure de mtk il ne parle a aucun moment du fichier .inf?????
bon la s'arrete mes competence alors place au pro pour m'aidez
merci
---------------
La réalité n'est qu'une illusion créée par le manque de Drogue....
