Bonjour,
Problème : j'ai un portable sur lequel depuis plus d'un an j'essaie de faire fonctionner ma carte pcmcia Netgear FA511 pour pouvoir utiliser internet sur ma Mandrake 10.1
A chaque fois, j'ai abandonné mais cette fois ci je veux y venir au bout.
Voici donc pleins d'informations (résultats de commande) :
Ordi portable : Packard Bell Easy Note Alpha
Systeme d'exploitation : Win XP / Mandrake 10.1
Carte PCMCIA pour connexion ethernet : Netgear FA511
Au lancement de Mandrake :
activation de l'inferface eth0 : disabling IRQ #9
(Rem : sous windows, c'est bien IRQ 9 qui est associé à la carte PCMCIA)
J'ai édité /etc/sysconfig/network-scripts/ifcfg-eth0 and set 'ONBOOT=no'.
---------------------------------------
Centre de controle Mandrake Linux
Périphérique :
Vendeur: ADMtek
Description: ADM985 10/100 cardbus ethernet controller
Classe de matériel: NETWORK_ETHERNET
Nom du module: tulip
Adresse matérielle: e00:10:7a:68:f8:55
Bus: PCI
Position sur le bus: 2
---------------------------------------
Les résultats des commandes suivantes :
ifconfig
cardctl ident
cardctl config
ifconfig -a
lsmod
lspci -v
cat /proc/interrupts
cat /proc/cmdline
service pcmcia restart
rpm -q devfsd
rpm -q udev
service udev status
cat /etc/modprobe.conf
cat /etc/pcmcia/misc.conf
cat /etc/pcmcia/network
ifonfig ----------------------------------------------------------------
[root@localhost louvino]# ifconfig
eth0 Lien encap:Ethernet HWaddr 00:10:7A:68:F8:55
adr inet6: fe80::210:7aff:fe68:f855/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:572 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:6 Adresse de base:0x4000
lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1055 errors:0 dropped:0 overruns:0 frame:0
TX packets:1055 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:83270 (81.3 Kb) TX bytes:83270 (81.3 Kb)
cardctl config ------------------------------------------------------
[root@localhost louvino]# cardctl config
Socket 0:
Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
interface type is "cardbus"
irq 6 [exclusive] [level]
function 0:
Socket 1:
not configured
cardctl ident -------------------------------------------------------
[root@localhost louvino]# cardctl ident
Socket 0:
product info: "N"
Socket 1:
no product info available
ifconfig -a -----------------------------------------------------------
[root@localhost louvino]# ifconfig -a
eth0 Lien encap:Ethernet HWaddr 00:10:7A:68:F8:55
adr inet6: fe80::210:7aff:fe68:f855/64 Scope:Lien
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:998 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:6 Adresse de base:0x4000
eth1 Lien encap:UNSPEC HWaddr 00-00-4C-E0-15-03-2A-4F-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:1008 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1775 errors:0 dropped:0 overruns:0 frame:0
TX packets:1775 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:139326 (136.0 Kb) TX bytes:139326 (136.0 Kb)
sit0 Lien encap:IPv6-dans-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lsmod ---------------------------------------------------------------------
[root@localhost louvino]# lsmod
Module Size Used by
md5 3584 1
ipv6 230916 12
rfcomm 32348 0
l2cap 19876 5 rfcomm
bluetooth 39076 4 rfcomm,l2cap
snd-seq-oss 31232 0
snd-seq-midi-event 6080 1 snd-seq-oss
snd-seq 47440 4 snd-seq-oss,snd-seq-midi-event
snd-pcm-oss 49480 0
snd-mixer-oss 17376 1 snd-pcm-oss
snd-via82xx 22372 1
snd-ac97-codec 69392 1 snd-via82xx
snd-pcm 81800 2 snd-pcm-oss,snd-via82xx
snd-timer 20356 2 snd-seq,snd-pcm
snd-page-alloc 7400 2 snd-via82xx,snd-pcm
gameport 3328 1 snd-via82xx
snd-mpu401-uart 5856 1 snd-via82xx
snd-rawmidi 19300 1 snd-mpu401-uart
snd-seq-device 6344 3 snd-seq-oss,snd-seq,snd-rawmidi
snd 45988 13 snd-seq-oss,snd-seq,snd-pcm-oss,snd-mixer-oss,snd-via82xx,snd-ac97-codec,snd-pcm,snd-timer,snd-mpu401-uart,snd-rawmidi,snd-seq-device
soundcore 7008 1 snd
af_packet 16072 1
ds 17572 4
eth1394 17000 0
ide-cd 37280 0
cdrom 37724 1 ide-cd
ohci1394 30788 0
ieee1394 292056 2 eth1394,ohci1394
tulip 43040 0
loop 12520 0
nls_iso8859-15 4224 1
nls_cp850 4480 1
vfat 11168 1
fat 39776 1 vfat
yenta_socket 18624 1
pcmcia_core 59972 2 ds,yenta_socket
via-agp 7360 1
agpgart 27752 1 via-agp
uhci-hcd 28752 0
usbcore 103172 3 uhci-hcd
lspci -v -------------------------------------------------------------------
[root@localhost louvino]# lspci -v
[...]
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: NEC Corporation: Unknown device 8137
Flags: bus master, medium devsel, latency 168, IRQ 6
Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001
00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: NEC Corporation: Unknown device 8137
Flags: bus master, medium devsel, latency 168
Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
16-bit legacy interface ports at 0001
[...]
02:00.0 Ethernet controller: Linksys 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 11)
Subsystem: Netgear: Unknown device 511a
Flags: bus master, medium devsel, latency 64, IRQ 6
I/O ports at 4000 [size=256]
Memory at 10800000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at 10400000 [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
cat /proc/interrupts ----------------------------------------------
[root@localhost louvino]# cat /proc/interrupts
CPU0
0: 498570 XT-PIC timer
1: 2453 XT-PIC i8042
2: 0 XT-PIC cascade
6: 0 XT-PIC yenta, eth0
9: 100001 XT-PIC ohci1394
11: 118 XT-PIC uhci_hcd, VIA686A
12: 9350 XT-PIC i8042
14: 4801 XT-PIC ide0
15: 483 XT-PIC ide1
NMI: 0
LOC: 498540
ERR: 968
MIS: 0
cat /proc/cmdline ---------------------------------------------------
[root@localhost louvino]# cat /proc/cmdline
BOOT_IMAGE=linux ro root=306 acpi=ht resume=/dev/hda5
service pcmcia restart ---------------------------------------------
[root@localhost louvino]# service pcmcia restart
Shutting down PCMCIA services: ERROR: Module pcmcia_core is in use by yenta_socket
done.
Starting PCMCIA services: cardmgr[4361]: watching 2 sockets
done.
rpm -q devfsd ---------------------------------------------------
[root@localhost louvino]# rpm -q devfsd
le paquetage devfsd n'est pas installé
rpm -q udev --------------------------------------------------------
[root@localhost louvino]# rpm -q udev
udev-030-24mdk
service udev status --------------------------------------------------
[root@localhost louvino]# service udev status
udev est en fonctionnement [ OK ]
cat /etc/modprobe.conf ----------------------------------------------
[root@localhost louvino]# cat /etc/modprobe.conf
# This file is autogenerated from /etc/modules.conf using generate-modprobe.conf command
alias eth0 tulip
alias sound-slot-0 snd-via82xx
remove snd-via82xx /sbin/modprobe -r snd-pcm-oss; /sbin/modprobe --first-time -r --ignore-remove snd-via82xx
install snd-via82xx /sbin/modprobe --first-time --ignore-install snd-via82xx && { /sbin/modprobe snd-pcm-oss; /bin/true; }
install usb-interface /sbin/modprobe uhci-hcd; /bin/true
alias eth1 eth1394
alias ieee1394-controller ohci1394
cat /etc/pcmcia/misc.conf ------------------------------------------
root@localhost pcmcia]# cat misc.conf
device "prism2_cs"
class "network" module "prism2_cs"
card "Advantech WLAN-9030"
manfid 0xd601, 0x0002
bind "orinoco_cs"
card "Tekram AIR.mate PCF 200 Wireless LAN card"
manfid 0x0274, 0x1613
bind "orinoco_cs"
cat /proc/pcmcia/network ---------------------------------------
[root@localhost pcmcia]# cat network
#! /bin/sh
#
# network.sample $Revision: 1.1 $ $Date: 1995/05/25 04:30:06 $ (David Hinds)
#
# Initialize or shutdown a PCMCIA ethernet adapter
#
# This script should be invoked with two arguments. The first is the
# action to be taken, either "start", "stop", or "restart". The
# second is the network interface name.
action=$1
device=$2
case "${action:?}" in
'start')
#
# We don't do *anything* here. We get a hotplug event when the ethX device
# is registered, and we bring the device up there
#
;;
'stop')
#
[ -f /etc/sysconfig/network-scripts/ifcfg-${device} ] && \
/etc/sysconfig/network-scripts/ifdown ifcfg-${device}
;;
'restart')
/sbin/ifconfig ${device:?} down up
;;
esac
