madsurfer Boulet's eradicator |  à tous,
Lilo ne veut pas booter sur le noyau par defaut (label = Linux) alors que tout me semble correctement défini.
Il reste sur le prompt, ce qui est génant lorsqu'il y a des coupures électriques (malheureusement). 
Donc si vous avez une idée sur le problème n'hésité pas. Je souhaiterais qu'au bout de 20 secondes si personne ne touche à rien, lilo lance le label Linux
Voici mon /etc/lilo.conf
Code :
- # /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
- # --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
- # and `/usr/share/doc/mbr/'.
- # +---------------------------------------------------------------+
- # | !! Reminder !! |
- # | |
- # | Don't forget to run `lilo' after you make changes to this |
- # | conffile, `/boot/bootmess.txt', or install a new kernel. The |
- # | computer will most likely fail to boot if a kernel-image |
- # | post-install script or you don't remember to run `lilo'. |
- # | |
- # +---------------------------------------------------------------+
- # Support LBA for large hard disks.
- #
- lba32
- # Overrides the default mapping between harddisk names and the BIOS'
- # harddisk order. Use with caution.
- #disk=/dev/hde
- # bios=0x81
- #disk=/dev/sda
- # bios=0x80
- # Specifies the boot device. This is where Lilo installs its boot
- # block. It can be either a partition, or the raw device, in which
- # case it installs in the MBR, and will overwrite the current MBR.
- #
- boot=/dev/hda
- # Specifies the device that should be mounted as root. (`/')
- #
- root=/dev/hda2
- # Enable map compaction:
- # Tries to merge read requests for adjacent sectors into a single
- # read request. This drastically reduces load time and keeps the
- # map smaller. Using `compact' is especially recommended when
- # booting from a floppy disk. It is disabled here by default
- # because it doesn't always work.
- #
- # compact
- # Installs the specified file as the new boot sector
- # You have the choice between: bmp, compat, menu and text
- # Look in /boot/ and in lilo.conf(5) manpage for details
- #
- install=/boot/boot-menu.b
- # Specifies the location of the map file
- #
- map=/boot/map
- # You can set a password here, and uncomment the `restricted' lines
- # in the image definitions below to make it so that a password must
- # be typed to boot anything but a default configuration. If a
- # command line is given, other than one specified by an `append'
- # statement in `lilo.conf', the password will be required, but a
- # standard default boot will not require one.
- #
- # This will, for instance, prevent anyone with access to the
- # console from booting with something like `Linux init=/bin/sh',
- # and thus becoming `root' without proper authorization.
- #
- # Note that if you really need this type of security, you will
- # likely also want to use `install-mbr' to reconfigure the MBR
- # program, as well as set up your BIOS to disallow booting from
- # removable disk or CD-ROM, then put a password on getting into the
- # BIOS configuration as well. Please RTFM `install-mbr(8)'.
- #
- # password=tatercounter2000
- # Specifies the number of deciseconds (0.1 seconds) LILO should
- # wait before booting the first image.
- #
- delay=20
- prompt
- # You can put a customized boot message up if you like. If you use
- # `prompt', and this computer may need to reboot unattended, you
- # must specify a `timeout', or it will sit there forever waiting
- # for a keypress. `single-key' goes with the `alias' lines in the
- # `image' configurations below. eg: You can press `1' to boot
- # `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
- #
- # message=/boot/bootmess.txt
- # prompt
- # single-key
- # delay=100
- # timeout=100
- # Specifies the VGA text mode at boot time. (normal, extended, ask, <mode> )
- #
- # vga=ask
- # vga=9
- #
- vga=normal
- # Kernel command line options that apply to all installed images go
- # here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
- # the Linux kernel `Documentation' directory.
- #
- # append=""
- # Boot up Linux by default.
- #
- default=Linux
- image=/boot/bzImage
- label=Linux
- read-only
- image=/boot/bzImage2418
- label=Linux-2418
- read-only
- image=/vmlinuz
- label=Linux_old
- read-only
- # restricted
- # alias=1
- image=/vmlinuz.old
- label=LinuxOLD
- read-only
- optional
- # restricted
- # alias=2
- # If you have another OS on this machine to boot, you can uncomment the
- # following lines, changing the device name on the `other' line to
- # where your other OS' partition is.
- #
- # other=/dev/hda4
- # label=HURD
- # restricted
- # alias=3
|
Message édité par madsurfer le 06-12-2005 à 08:41:03
|
