vala ce que me sort pnpdump
sma l'air vu que c'est compliqué
ensuite je dois décommenter les lignes correspondantes
à la config que je veuc faire mais j'en fait quoi ensuite de ce fichier ????
# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
#
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of the output file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
#
# Trying port address 0273
# Board 1 has serial identifier 27 ff ff ff ff 68 18 73 16
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 27 ff ff ff ff 68 18 73 16)
# Vendor Id ESS1868, No Serial Number (-1), checksum 0x27.
# Version 1.0, Vendor version 1.0
# ANSI string -->Maxi Sound 64 Series<--
#
# Logical device id ESS8600
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 0
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0800
# Maximum IO base address 0x0ff8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0800))
(NAME "ESS1868/-1[0]{Maxi Sound 64 Series}" )
# (ACT Y)
))
#
# Logical device id ESS8601
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 1
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 0 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Fixed IO base address 0x0220
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Fixed IO base address 0x0388
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Fixed IO base address 0x0300
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0300))
# Start dependent functions: priority acceptable
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 0 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5, 7, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Fixed IO base address 0x0388
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Fixed IO base address 0x0300
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0300))
# Start dependent functions: priority acceptable
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Fixed IO base address 0x0388
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0300))
# Start dependent functions: priority acceptable
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Fixed IO base address 0x0388
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0800
# Maximum IO base address 0x0ffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0800))
# Start dependent functions: priority functional
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0800
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0800))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0800
# Maximum IO base address 0x0ffe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 2 (SIZE 2) (BASE 0x0800))
# End dependent functions
(NAME "ESS1868/-1[1]{Maxi Sound 64 Series}" )
# (ACT Y)
))
#
# Logical device id ESS8602
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 2
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Fixed IO base address 0x0201
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0201))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x020f
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0200))
# End dependent functions
# Compatible device id PNPb02f
(NAME "ESS1868/-1[2]{Maxi Sound 64 Series}" )
# (ACT Y)
))
#
# Logical device id ESS8603
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ESS1868/-1 (LD 3
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 9.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 9 (MODE +E)))
# Fixed IO base address 0x0330
# Number of IO addresses required: 6
# (IO 0 (SIZE 6) (BASE 0x0330))
# Start dependent functions: priority acceptable
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0ff0
# IO base alignment 16 bytes
# Number of IO addresses required: 6
# (IO 0 (SIZE 6) (BASE 0x0330))
# End dependent functions
(NAME "ESS1868/-1[3]{Maxi Sound 64 Series}" )
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
---------------
Je suis moi juste moi et pas le produit de mon orgueil et de ma vanité
