J'ai une Mandrake v8.2 avec un lecteur cdrom et un graveur, respectivement /dev/hda et /dev/scd0
J'ai consulté la page de DarkSchneider, et j'ai donc vérifié les fichiers modules, lilo.conf (avec le paramètre append adéquat) et les différents conseils prodigués.
Or de fait à l'installation de la Mdk 8.2 tout y est.
J'ai vérifié les liens symboliques dans /dev et /dev/cdroms, aucun n'est rompu, ils pointent bien vers les bons endroits semble-t-il.
J'ai verifié avec cdrecord -scanbus, et tout semble ok :
cdrecord -scanbus
Cdrecord 1.11a19 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002 Jörg Schilling
Linux sg driver version: 3.1.22
Using libscg version 'schily-0.6'
scsibus0:
0,0,0 0) 'PLEXTOR ' 'CD-R PX-W1210A' '1.10' Removable CD-ROM
0,1,0 1) *
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
J'ai essayé de graver a maintes reprise des images iso, sans y arriver (différentes images pour être sûr), avec su pour être sûr d'avoir les permissions nécessaires. Voilà ce que j'obtiens :
# cdrecord -v -dao speed=4 dev=0,0,0 image.iso
Cdrecord 1.11a19 (i586-mandrake-linux-gnu) Copyright (C) 1995-2002 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.22
Using libscg version 'schily-0.6'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'PLEXTOR '
Identifikation : 'CD-R PX-W1210A'
Revision : '1.10'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 2097152 = 2048 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 311 MB
Total size: 358 MB (35:29.49) = 159712 sectors
Lout start: 358 MB (35:31/37) = 159712 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 7
Is not unrestricted
Is not erasable
ATIP start of lead in: -11538 (97:28/12)
ATIP start of lead out: 338025 (75:09/00)
Disk type: Long strategy type (Cyanine, AZO or similar)
Manuf. index: 7
Manufacturer: GIGASTORAGE CORPORATION
Blocks total: 338025 Blocks current: 338025 Blocks remaining: 178313
Starting to write CD/DVD at speed 4 in write mode for single session.
Last chance to quit, starting real write in 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Performing OPC...
Sending CUE sheet...
Writing pregap for track 1 at -150
cdrecord: Input/output error. write_g1: scsi sendcmd: cmd timeout after 1.300 (200) s
CDB: 2A 00 FF FF FF 89 00 00 1F 00
cmd finished after 1.300s timeout 200s
write track pad data: error after 63488 bytes
cdrecord: Input/output error. read buffer cap: scsi sendcmd: no error
CDB: 5C 00 00 00 00 00 00 00 0C 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 29 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset occurred) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.200s timeout 200s
Starting new track at sector: 0
Track 01: 0 of 311 MB written.cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: F0 00 03 00 00 00 21 0A 00 00 00 00 0C 09 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x0C Qual 0x09 (write error - loss of streaming) Fru 0x0
Sense flags: Blk 33 (valid)
cmd finished after 0.000s timeout 200s
write track data: error after 0 bytes
Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
Writing time: 47.750s
Fixating...
cdrecord: Input/output error. flush cache: scsi sendcmd: no error
CDB: 35 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 2C 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x2C Qual 0x00 (command sequence error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.000s timeout 200s
Trouble flushing the cache
Fixating time: 0.001s
cdrecord: fifo had 64 puts and 1 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
[img]
La seule chose que j'arrive à réaliser c'est d'effacer des CDRW.
Pas génial.
J'ai aussi essayé des GUI, mais bien sûr cela ne marche pas d'avantage.